Matrix T1XE-04 Скачать руководство пользователя страница 11

Страница: 11 / 86

3.5 aUTo CalibraTioN iNSTrUCTioNS

Run Auto Calibration to calibrate incline after assembly and after

replacing any electronic component.

aUTo CalibraTioN ProCedUre:

1) Press ENTER, 2, 0, 0, 1, then ENTER. Engineering Mode will

appear on the display.

2) Press the button next to CALIBRATION..

3) Press the button next to AUTO CALIBRATION. You SHOULD NOT

be standing on the unit while it is calibrating.

4) After completion, the display either return to normal operation

(indicating that calibration passed) or say Auto Calibration failed.

5)PressthebuttonnexttoBACKthenthebuttonnexttoHOMEto

return to normal operation mode. You can also press the Emergency

Stop.

3.6 adjUSTiNG THe rUNNiNG belT

After placing the treadmill in the position it will be used, the belt

must be checked for proper tension and centering. The belt may

need to be adjusted after the first 2 hours of use. Temperature,

humidity, and use cause the belt to stretch at different rates. If

the belt starts to slip when a user is on it, be sure to follow the

directions below.

STeP 1:

Locate the two hex head bolts on the rear of the treadmill.

The bolts are located at each end of the frame at the back of the

treadmill. These bolts adjust the rear roller. Do not adjust until the

treadmill is on. This will prevent over tightening of one side.

STeP 2:

The belt should have equal distance on either side

between the frame. If the belt is touching one side, do not start

the treadmill. Turn the bolts counter clockwise approximately one

full turn on each side. Manually center the belt by pushing the belt

from side to side. Tighten the bolts the same amount as when the

user loosened them, approximately one full turn. Inspect the belt

for damage.

STeP 3:

While the treadmill is running at 3 mph, observe the belt

position. If it is moving to the right, tighten the right bolt by turning

it clockwise 1/4 turn, and loosen the left bolt 1/4 turn. If it is moving

to the left, tighten the left bolt by turning it clockwise 1/4 turn and

loosen the right 1/4 turn. Repeat Step 3 until the belt remains

centered for several minutes.

STeP 4:

Check the tension of the belt. The belt should be very

snug. When a person walks or runs on the belt, it should not

hesitate or slip. If this occurs, tighten the belt by turning both bolts

clockwise 1/4 turn. Repeat if necessary.

CHaPTer 3: PreVeNTaTiVe maiNTeNaNCe

Содержание T1XE-04























































































Результаты поиска

Содержание T1XE-04

Отзывы:

Похожие инструкции для T1XE-04

Бренды по названию

Популярные бренды

Matrix T1XE-04, Руководство по обслуживанию

Результаты поиска

Содержание T1XE-04

Отзывы:

Похожие инструкции для T1XE-04

Бренды по названию

Популярные бренды