manualshive.com logo in svg

Matrix Switch Corporation MSC-GCP2U32, Руководство по эксплуатации продукта, Страница: 21 / 75

Поделиться
Скачать
Matrix Switch Corporation MSC-GCP2U32 Скачать руководство пользователя страница 21

Parameters include the following:

1. DHCP Enable
2. IP Address
3. Netmask
4. Gateway
5. Primary DNS
6. Secondary DNS
7. Router IP

Note:

 After changing network parameters, the system needs to be restarted for the changes to take effect.  The 

"Reboot on change"

 can be used for this purpose by navigating to it, pressing the 

Select

 button and confirming

the 

Reboot

 dialog.

DHCP

 can be enabled or disabled by navigating to it and pressing the 

Select

 button to toggle the current state.  

If enabled the remaining network settings (except 

Router IP

) are not used and the network configuration will 

be obtained from the network's DHCP server.

To set any of the remaining IP address settings, navigate to the parameter of interest and press the 

Select

 button 

to enter 

Edit Mode

.  The first decimal number will be highlighted, awaiting input.  Enter the desired value with 

the 

Number

 buttons 

0

 through 

9

.  The 

Right

 or 

Left

 arrows are used to select the next or previous IP address 

decimal number.  To exit 

Edit Mode

 press the 

Select

 or 

Save

 buttons to store the new value or 

Cancel

 to 

discard the entered value and use the old one.

If DHCP is not enabled, the MSC-GCP2U32 will use the manual network configuration.  This includes the 
following settings: 

IP Address

 (192.168.2.80 by default), 

Netmask

 (255.255.255.0 by default) and 

Gateway

 

(192.168.2.1 by default).  The Gateway address is only used when controlling routers outside of the current IP 
subnet.  The 

Primary

 and 

Secondary

 DNS entries are not currently needed and default to 0.0.0.0.

The 

Router IP

 setting allows for assigning the IP address of a single router to control.  Setting up multiple 

router control profiles currently requires using the web page or command protocol interfaces for configuration, 
although the panel can be used to select between the available profiles.

2.7.3 Matrix Profile

The 

Matrix Profile

 page is accessed from the 

Config Menu

 and can be used to select the active router control 

Page 21 of 75

©

 2013 Matrix Switch Corporation

www.matrix-switch.tv

Figure 12: Network Config

Содержание MSC-GCP2U32












































































Отзывы:

Нет отзывов