background image

 

Troubleshooting 

Page 20 

 

 

 

Troubleshooting 

If the spread pattern is not satisfactory, this may be due to the following reasons: 

 

Inconsistent properties of the spread material: different density, grain form or 
moisture content 

 

Clotting of the spread material 

 

Spread material is blown away by strong wind 

 

Clogging or bridging by foreign objects 

 

Uneven terrain  

 

Worn agitator fingers 

 

Incorrect input rpm  

 

Incorrect speed 

 

Maintenance 

7.1 

General information 

 

 

 

 

 

 

 

 

 

 

 

 

 
Attention! 
Personal injury or damage to the tractor and the implements can occur. 
Before each use of the implements check all safety-relevant parts and the 
hydraulic connections. 

 

 

Danger!  
Only perform service and maintenance tasks when the tractor is 
switched off.  

 

 
 

Attention!  
Remove the ignition key before performing maintenance tasks on the 
implement.  

 

 

Attention! 
Danger of crushing due to moving parts. 
Never reach into the crushing hazard zone if parts are moving or can move. 
 
If there is pressure loss there is danger of crushing and shear injuries in the 
lift-out mechanism.  
 
 
 
 
 
 
 

Содержание SPR-HM-100






























Отзывы: