manualshive.com logo in svg

masosine SPS 100, Руководство пользователя

Поделиться
Скачать
masosine SPS 100 Скачать руководство пользователя страница 81

Fitting the front liner

•

Push the front liner into position, pushing evenly at both ends so that it does not jam. The anti-

rotation pins within the pump housing (arrowed) guarantee that the liner is properly positioned.
The two liners are identical.

Fitting the front cover

•

Check that the front cover O-ring (arrowed) is in its groove in the front cover.

•

Fit the front cover over the shaft, the front support and the pump housing studs.

•

Fit the cap nuts (right-hand thread) and washers to the pump housing studs. Use a 22mm spanner.
Tighten them to 45Nm (torque for other sizes see "Tightening torques" on page 89)

Assembling the pump housing— pumps with a stainless steel power frame and a single
mechanical seal

Note

: See " Fitting the pump housing—pumps with a single mechanical seal" on page 76 for assembling

the pump housing of a pump with a cast iron power frame.

m-SPS-en-08

81

Содержание SPS 100












































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды