masosine SPS 100 Скачать руководство пользователя страница 79

Страница: 79 / 139

Fitting the rotor, the gate and the gate guide

The gate and gate

guide

The gate and

gate guide oriented for

clockwise rotor rotation

The gate and gate guide orient-

ed for counter- clockwise rotor

rotation

Pressure

side

Suction

side

Suction

side

Pressure

side

•

Check that the two rotor O-rings (visible one arrowed) are in position on both sides of the rotor.

•

Position the gate within the gate guide and hold as one unit.

Check that the gate and gate guide are correctly oriented for the desired sense of
rotor rotation. This is critical for proper operation.

•

Hold the rotor vane in the slot of the gate. The rotor is reversible. Use two hands to position the

rotor, the gate and the gate guide together. Push the assembly into position. The gate and gate
guide slide freely into their channel; the splines within the rotor hub must be aligned with the shaft
splines.

•

Ensure that the rotor is pushed all the way home.

m-SPS-en-08

Содержание SPS 100












































































































































Результаты поиска

Содержание SPS 100

Отзывы:

Бренды по названию

Популярные бренды

masosine SPS 100, Руководство пользователя

Результаты поиска

Содержание SPS 100

Отзывы:

Бренды по названию

Популярные бренды