masosine SPS 100 Скачать руководство пользователя страница 69

Страница: 69 / 139

22.4 Dismantling and assembling the SPS 250, SPS 300, SPS 400

and SPS 500

Dismantling the SPS 250 SPS 300 SPS 400 and SPS 500

Note

: The SPS 250, SPS 400 and the SPS 500 are similar.

Note

: The pictures show a pump with a cast iron power frame. Dismantling models with stainless steel

power frame is similar. For exceptions, see "Dismantling the pump housing—pumps with a stainless steel
power frame and a single mechanical seal" on page 75.

Removing the front cover

•

Use a 22mm spanner to remove the cap nuts

(right-hand thread)

and washers.

•

Lightly tap the two front cover pins if necessary and use them to pull off the cover.

The cover is heavy.

•

You can now access the front cover O-ring (arrowed) in its groove in the front cover.

Removing the front liner

•

Pull the front liner to remove it.

Note

: You may find it convenient to turn the pump shaft and rotor a little to create space for your

fingertips to grasp the top of the front liner.

m-SPS-en-08

Содержание SPS 100












































































































































Результаты поиска

Содержание SPS 100

Отзывы:

Бренды по названию

Популярные бренды

masosine SPS 100, Руководство пользователя

Результаты поиска

Содержание SPS 100

Отзывы:

Бренды по названию

Популярные бренды