manualshive.com logo in svg

masosine SPS 100, Руководство пользователя

Поделиться
Скачать
masosine SPS 100 Скачать руководство пользователя страница 45

Fitting the rear liner—all SPS 100 pumps

•

Push the rear liner into position, pushing evenly at both ends so that it does not jam. The anti-

rotation pins within the pump housing (arrowed) guarantee that the liner is properly positioned.
The two liners are identical.

Fitting the rotor, the gate and the gate guide

This end 

in first

Note gate

orientation

within the

guide

The gate and gate guide inverted to show the
gate’s position within the guide for counter-
clockwise rotor rotation

The rotor

The gate and 

gate guide oriented for 

 clockwise rotor rotation

The gate and  gate guide 

oriented for counter- clockwise 

rotor rotation

Pressure 

side

Suction 

side

Suction 

side

Pressure 

side

•

Check that the rotor O-ring is in position.

•

Position the gate within the gate guide and hold as one unit.

Check that the gate and gate guide are correctly oriented for the desired sense of
rotor rotation. This is critical for proper operation.

m-SPS-en-08

45

Содержание SPS 100












































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды