masosine SPS 100 Скачать руководство пользователя страница 46

Страница: 46 / 139

•

Hold the rotor vane in the slot of the gate, with the larger diameter end of the rotor bush away

from you. Position the rotor, the gate and the gate guide together. Push the assembly into
position. The gate and gate guide slide freely into their channel; the splines within the rotor hub
must be aligned with the shaft splines.

•

Ensure that the rotor is pushed all the way home.

Fitting the front bushing and the front liner

•

Push the front bushing into position, thick end (arrowed) first. (The two bushings are identical.)

Note

: Pumps are fitted with identical front and rear bushings.

•

Push the front liner into position, pushing evenly at both ends so that it does not jam. The anti-

rotation pins within the pump housing (arrowed) guarantee that the liner is properly positioned.
The two liners are identical.

m-SPS-en-08

Содержание SPS 100












































































































































Результаты поиска

Содержание SPS 100

Отзывы:

Бренды по названию

Популярные бренды

masosine SPS 100, Руководство пользователя

Результаты поиска

Содержание SPS 100

Отзывы:

Бренды по названию

Популярные бренды