MARLOW-HUNTER MH31, Руководство оператора

Страница: 208 / 267

Sails and Rigging
12.8
starboard sheave position within the boom.
Lash the sail end of the outhaul to the aft boom end
until the mainsail is ready for installation.
12.7.6 Traveler Lines Installation
Verify or route both traveler lines as described in
the Running Rigging section above (see also Fig.
12.22).
Route the each line’s control ends through the port
and starboard cleat block.
12.7.7 Mainsheet Installation
Verify or route the mainsheet as described in the
Running Rigging section above (see also Figures
12.21 and 12.22).
The mainsheet should be routed through the out-
board starboard sheave position within the boom.
Route the control line through the single sheet stop-
per located on the port arch rail.
12.7.8 Vang Installation (Conventional & Solid)
Place the vang on the deck immediately aft of the
mast. Position the end with the vang cable facing
aft.
Refer to Fig. 12.23 and attach the vang hardware as
directed based on the type of vang (rope or solid).
Route the vang line as illustrated in Fig. 12.23.
From the mast base block, the line continues to the
port organizer for a standard rig or the starboard
organizer for a furling rig. From there it travels under
the sea hood and on to the sheet stopper.
12.7.9 Mainsail Installation
NOTE: Raising the mainsail should not be done with the wind astern.
For the standard rig mainsail, complete the following
steps:
Lower the main halyard and attach the halyard shack-
le to the clew of the mainsail head.
Provide some slack to the mainsheet.
Open and remove the inspection port cover near the
sail feeder.
Insert the first mainsail slider into the aft mast grove.
3.
1.
2.
1.
2.
3.
1.
2.
3.
4.
1.
2.
3.
4.
Continue feeding the mainsail sliders into the groove
while rasing the main halyard until all sliders are
installed..
Back the remaining luff down the grove until it can be
connected to the tack hook).
Replace the mast inspection cover.
Route the halyard control line down to the mast base
block and continue as described in the Running
Rigging section above.
Position the foot of the sail along the boom and atta-
che the boom outhaul to the clew as described in the
Running Rigging section above.
For the furling rig mainsail, complete the following steps:
Open and remove the 2 inspections covers on the
mast’s port side (press button, push up or down, lift
opposite end and remove).
Locate the sail feeding location on the luff extrusion
from the top inspection opening.
Feed the head of the sail through the mast slot and
into the main foil (Fig. 12.6).
Lower the main halyard and attach the halyard shackle
to the strap sewn onto the mainsail head (Fig. 12.6).
Continue feeding the mainsail into the extrusion while
rasing the main halyard until the luff is fully inserted
into the extrusion.
Back the remaining luff down the extrusion from the
sail entry location until it can be connected to the tack
hook through the lower inspection port (Fig. 12.6).
Replace the mast inspection covers.
Route the halyard control line down to the mast base
block and continue as described in the Running
Rigging section above.
Position the foot of the sail along the boom and atta-
che the boom outhaul to the clew as described in the
Running Rigging section above.
12.7.10 Main Furling Line Installation
Place a loop of the furling line around the furling
winch (Fig. 12.7).
Route both sides of the loop to the mast blocks.
Remove the sheaves from the blocks and position the
lines around the sheaves and replace in the blocks.
Continue the lines as described in the Running
Rigging section above. The organizer and sheet
5.
6.
7.
8.
9.
1.
2.
3.
4.
5.
6.
7.
8.
9.
1.
2.
3.