Manitou MT 1135 ST3B, Инструкция по эксплуатации

Страница: 80 / 159

2 - 49
C - HYDRAULIC MOVEMENT CUT-OFF CONFIGURATION
IMPORTANT
The cut-off of "AGGRAVATING" hydraulic movements has two possible configurations. Consult your dealer to change this configuration.
Your configuration can be identified simply by driving. If indicator lamp C1 is off, configuration 1 is enabled, indicator lamp C1 is lit, configuration 2 is enabled.
CONFIGURATION 1 HALTED
SLOW SPEED
1 to 3 km/h
SPEED
> 3 km/h
TELESCOPE(S) IN
RETRACTED POSITION
"HANDLING" MODE
A4-A5: Very slow intermittent sound alarm.
A6: Slow intermittent sound alarm.
A7: Fast intermittent sound alarm.
A8: Very fast intermittent sound alarm.
No sound alarm.
No sound alarm.
The "AGGRAVATING"
hydraulic movement
cut-off function is
disconnected.
"BUCKET" MODE
A6: A beep upon passing into the red zone.
"SUSPENDED LOAD"
MODE
A4-A5: Very slow intermittent sound alarm.
A6: Slow intermittent sound alarm.
A7: Fast intermittent sound alarm.
A8: Very fast intermittent sound alarm.
No sound alarm.
CONFIGURATION 2 HALTED
SLOW SPEED
1 to 5 km/h
SPEED
> 5 km/h
TELESCOPE(S)
RETRACTED
"HANDLING" MODE
A4-A5: Very slow intermittent sound
alarm.
A6: Slow intermittent sound alarm.
A7: Fast intermittent sound alarm.
A8: Very fast intermittent sound
alarm.
A7: Fast intermittent sound alarm.
A8: Very fast intermittent sound
alarm.
When indicator lamp C1 is lit,
the "AGGRAVATING" hydraulic
movement cut-off function is
disconnected.
No sound alarm.
When indicator lamp C1 is lit,
the "AGGRAVATING" hydraulic
movement cut-off function is
disconnected.
No sound alarm.
When indicator lamp C1
is lit, the "AGGRAVATING"
hydraulic movement
cut-off function is
disconnected.
C1
"BUCKET" MODE
A6: A beep upon passing into the
red zone.
A6: A beep upon passing into the
red zone.
When indicator lamp C1 is lit,
the "AGGRAVATING" hydraulic
movement cut-off function is
disconnected.
No sound alarm.
When indicator lamp C1 is lit,
the "AGGRAVATING" hydraulic
movement cut-off function is
disconnected.
"SUSPENDED LOAD"
MODE
A4-A5: Very slow intermittent sound alarm.
A6: Slow intermittent sound alarm.
A7: Fast intermittent sound alarm.
A8: Very fast intermittent sound alarm.
D - DISABLING “AGGRAVATING” HYDRAULIC MOVEMENT CUT-OFF
IMPORTANT
Remain very vigilant during this operation. The only information available to the operator is the lift truck’s dynamic
stability.
Authorization of this function can be configured from the OPT menu in the menu screen.
In certain cases, in order to get out of a difficult situation, the operator can bypass
this safety system. Button D temporarily disables the cutting-off of "AGGRAVATING"
hydraulic movements.
- Hold down button D (indicator lamps C1 and D1 lamp will light (60 second time
delay)), and at the same time perform the necessary “AGGRAVATING” hydraulic
movement with extreme care.
E - TESTING OF THE LONGITUDINAL STABILITY LIMITER AND WARNING DEVICE
- Short press the button to verify at any time that the longitudinal stability
alarm is working.
• Correct operation: All the LEDs A1 to A8 light for two seconds and an audible
beep is sounded.
NOTE: This test does not check the proper adjustment of the longitudinal stability
limiter that must be inspected daily or after every 10 hours of service (see: 3 -
MAINTENANCE: A - DAILY OR EVERY 10 HOURS SERVICE).
A8
A7
A6
A5
A4
A3
A2
A1
C1
D
D1
647104
(13/06/2016)
MT
835
/ 1135
/ 1335
ST3B