![background image](http://html1.mh-extra.com/html/makita/n1923bj/n1923bj_instruction-manual_4056049006.webp)
ENGLISH
Explanation of general view
1
Bolt
2
Drum
3
Planer blade
4
Drum cover
5
Adjust plate
6
Blade edge
7
Screws
8
Heel
9
Back side of gauge base
0
Inside edge of gauge plate
q
Gauge plate
w
Gauge base
e
Pan head screw
r
Planer blade locating lugs
t
Heel of adjust plate
y
Set plate
u
Inside flank of gauge plate
i
Mini planer blade
o
Hex. flange head bolt
p
Groove
a
Knob
s
Switch trigger
d
Lock button/
Lock-off button
f
Start
g
End
h
Blade edge
j
Cutting line
k
Screw
l
Edge fence
;
‘‘V’’ groove
z
Front base
x
Align the ‘‘V’’ groove with the
edge of the workpiece.
c
Nozzle assembly
v
Chip cover screw
b
Chip cover
n
Fit pin on nozzle assembly
into this hole.
m
Sharpening holder
,
Wing nut
.
Blade (A)
/
Blade (B)
¡
Side (C)
™
Side (D)
£
Chip cover
¢
Makita vacuum cleaner
∞
Limit mark
§
Screwdriver
¶
Brush holder cap
SPECIFICATIONS
Model
1923B/N1923B
Planing width ................................................. 82 mm
Planing depth ................................................... 1 mm
Shiplapping depth .......................................... 23 mm
No load speed (RPM) .................................... 16,000
Overall length ............................................... 293 mm
Net weight ....................................................... 2.9 kg
• Due to the continuing program of research and
development, the specifications herein are subject
to change without prior notice.
• Note: Specifications may differ from country to
country.
Power supply
The machine should be connected only to a power
supply of the same voltage as indicated on the
nameplate, and can only be operated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
Safety hints
For your own safety, please refer to enclosed Safety
instructions.
These symbols mean:
Read instruction manual.
DOUBLE INSULATION
ADDITIONAL SAFETY RULES
1. Rags, cloth, cord, string and the like should
never be left around the work area.
2. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
3. Handle the blades very carefully.
4. Be sure the blade installation bolts are
securely tightened before operation.
5. Hold the machine firmly with both hands.
6. Keep hands away from rotating parts.
7. Before using the machine on an actual work-
piece, let it run for a while. Watch for vibration
or wobbling that could indicate poor installa-
tion or a poorly balanced blade.
8. Make sure the blade is not contacting the
workpiece before the switch is turned on.
9. Wait until the blade attains full speed before
cutting.
10. Keep at least 200 mm away from the machine
at all times.
11. Always switch off and wait for the blades to
come to a complete stop before any adjusting.
12. Never stick your finger into the chip chute.
Chute may jam when cutting damp wood.
Clean out chips with a stick.
13. Do not leave the machine running. Operate the
machine only when hand-held.
14. When leaving the planer, switch off and set it
with the front base up on a wooden block, so
that the blades do not contact anything.
15. Always change both blades or covers on the
drum, otherwise the resulting imbalance will
cause vibration and shorten machine life.
16. Wait for complete run-down before putting the
machine aside.
17. Use only Makita blades specified in this
manual.
SAVE THESE INSTRUCTIONS.
6
1923B/N1923B (Eng) (’97. 7. 8)
Содержание N1923BJ
