manualshive.com logo in svg

Magnum ZC, Руководство пользователя

Поделиться
Скачать
Magnum ZC Скачать руководство пользователя страница 8

MAGNUMZC MANUAL – April 2006

PAGE  - -

8

8.

NEGATIVE PRESSURE IN THE HOUSE

ü

With no fire, there should be sufficient draft to exhaust cigarette smoke or other smoke introduced under
the baffle.  If the chimney has been installed properly and is operating properly, then the smoke should
go up the flue.  Chimneys that have an installation deficiency, or one or more of the above problems,
may be drawing cold air down the flue and into the room.  These chimneys will often smoke temporarily
on startup until the chimney is heated up.  Closing upstairs windows and opening a nearby window will
help to overcome smoking caused by house depressurization.

IMPORTANT POINTS:

•

Use Solid Fuel Only

ü

Do not

 block the hot air vents or air inlet to the fireplace, as this will cause the fireplace to overheat.

ü

Never

 start a fire using gasoline, kerosene, charcoal lighter fluid, or any other combustible liquid.

ü

Do not

 burn coal.  The sulfur in coal will corrode the firebox.

ü

Do not

 burn driftwood that has been in the ocean or salt water.  The salt will corrode the firebox and

chimney.

ü

Do not

 operate the unit with the doors partially open (except on startup), or with one door open, since

this may cause smoke to be drawn into the room.  (Doors must be fully open or fully closed.)

ü

Do not

 burn wood in the area in front of the log guard or a log grate (if used).

ü

Do not

 abuse the unit by over firing or by burning paper, cardboard or construction material such as

pressed wood, plywood, or lumber.

ü

Do not

 allow the wood to smolder or burn without flame, since this will produce excessive creosote

and cause the glass to become dirty.

ü

Warning:

Never use substitute glass materials.  If the glass needs replacement, order glass #AR-1400

from your

MAGNUM ZC

 dealer.

ü

Warning:

 Do not slam doors shut – Do not hit doors with logs, this can cause serious damage to

doors and/or break the high temperature glass.

ü

Keep small children away from fireplace.

  Front surfaces are extremely hot.

ü

Warning:

 Do not clean door glass while hot.  Wait for unit to cool down before servicing or cleaning.

ASHES

Remove ashes only when the fire is out and the ashes are cold.  Place the ashes in a metal container with a
tight fitting lid.  Do not put ashes in a cardboard box, and do not place the container on or near
combustible material.  The ashes remain hot for days and can start a fire.  Do not leave the ashes in the
house as they give off carbon monoxide and other toxic gases.

Stirring the ashes in the firebox occasionally when loading wood will cause them to burn thoroughly and
reduce the need for removing the ashes.

Содержание ZC







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды