manualshive.com logo in svg

Magnum ZC, Руководство пользователя

Поделиться
Скачать
Magnum ZC Скачать руководство пользователя страница 32

MAGNUMZC MANUAL – April 2006

PAGE  - -

32

GAS LOG SETUP   HOLE LOCATION

ZC-25 Gold Grill Trim Installation

Tools / Materials needed:   Red high-temp silicone

•

There are (2) two ways that you can apply the ZC-25 kit to the grills on the
Magnum ZC fireplace.  The first way is to install them with the grills on the
fireplace and the second is to take the grills off and lay them down on
newspaper.  The second way is the preferred way.

•

Unwrap the ZC-25 kit and lay the pieces where they will not get scratched as
you install them.  There is a protective plastic coating on the grill slats so you
will have to take it off before operating the fireplace.  It is best to leave it on
while you install the kit but start the edges of the plastic so it will be easier to
take off later.

•

If you are installing the kit with the grills left on the fireplace you will have to
make sure that the silicone is set before letting go of the gold grill slat.  If the kit
slides while curing it will be crooked.

•

Place a small amount of red silicone (app. 1/8” dia.) in (4) four spots toward the
front edge of the existing black grill slat. (see drawing)  It is best to do one grill
slat at a time so that the silicone does not get on everything.

•

Install the gold grill slat with the back edge raised up so that the silicone does
not get on it until you have placed the grill slat in place.  Push the gold grill slat
all the way up against the front edge of the black grill slat until the rounded
edge covers the front edge of the black grill slat.  Continue this until all of the
grill slats are in place.  Let the grill set until the silicone has cured (normally 15
to 20minutes) Do not start a fire in the fireplace until the silicone has cured for
24 hours.

Black grill slat

1/8”  dia.
silicone

Slide grill slat up against
front edge of black slat

Raise back of gold grill slat as
it is installed, then press down
onto the black grill slat

Содержание ZC







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды