Magnum ZC Скачать руководство пользователя страница 36

Страница: 36 / 38

MAGNUMZC MANUAL – April 2006

PAGE - -

Smoke comes into the room when

the doors are opened or when the fire
is first started

♦

Chimney damper not open

♦

Chimney not high enough

♦

Chimney cap blocked or too
close to the flue

♦

Depressurization inside the home

♦

Ice build-up on chimney cap/top

♦

Chimney needs cleaning

♦

Adjacent trees, buildings, etc too
close

♦

Poorly insulated chase way

Open damper control full open.

Check the chimney system to
make sure that it is the proper
height and clean.

Open a window and correct the
problem.

Clean Chimney System

Make sure that the installation
was done properly and the chase
way was insulated.

PROBLEMS

CAUSES

SOLUTIONS

Glass gets dirty fast

♦

Wet wood

♦

Not enough combustion-air

♦

Chimney not high enough

♦

Depressurization in the home

Use only well seasoned wood

Open combustion-air control

Check the chimney system

Open a window/correct problem

Unit won’t generate heat

♦

Wood is not well seasoned or is
wet from snow or rain

♦

Not enough wood being used

♦

Not enough grill opening

♦

Not enough combustion-air

♦

Too much chimney draft

Use only dry well seasoned
wood.

Add extra wood on the fire.

Do not block the grill opening.

Open combustion-air control.

Close draft control. Restrict the
draft on top of the chimney.

Содержание ZC







































Результаты поиска

Содержание ZC

Отзывы:

Бренды по названию

Популярные бренды

Magnum ZC, Руководство пользователя

Результаты поиска

Содержание ZC

Отзывы:

Бренды по названию

Популярные бренды