manualshive.com logo in svg

Magnum ZC, Руководство пользователя

Поделиться
Скачать
Magnum ZC Скачать руководство пользователя страница 13

MAGNUMZC MANUAL – April 2006

PAGE  - -

13

Read these instructions and keep them for future reference.  Before installing your fireplace, consult your
local building authority to obtain a building permit as well as information on the specific requirements in
your area.  Install the fireplace only as described in these instructions and using only approved components.
The

MAGNUM ZC

 is not intended for use with a gas log other than the factory supplied SP-40-ZC gas

retrofit system.  Failure to follow these instructions will void the certification and the warranty of the
fireplace, and may result in an unsafe installation.

NOTE:

  The

MAGNUM ZC

 can only be installed with 8” or 7” diameter listed type 2100’ HT insulated

or air- cooled chimney

.  It is strongly recommended to use 8” diameter chimney whenever possible.

If you are not using our UGA-B-32-ZC upper grill you must have a minimum of 125 square inches
of open area to allow the heat to exit the unit.  If you are using remote ducting you must have a
minimum of 100 square inches of open area in the front heat outlet of the unit.

The MAGNUM ZC is not tested for use with a masonry chimney or with a chimney liner

.

REPLACEMENT PARTS:

ü

R-102  

-Arched Ceramic 1400 Degree Replacement Glass (Specify left or right)

ü

R-105 (per door)  -Thermo-Tape Gasketing for glass seal

ü

R-106 (per door)  -Thermo-Cord Gasketing for door seal (includes gasket cement)

ü

R-116                    - Spring Door Handles (each door)

ü

R-120  

-Right 

Handle 

Kit 

(Steel)

ü

R-121  

-Left 

Handle 

Kit 

(Steel)

ü

R-145  

-Glass 

hold 

down 

clip 

(each)

ü

R-146  

-Glass 

hold 

down 

clip 

screw 

(each)

Listed:

  Warnock Hersey February 1994 Test Date

Standards:

  UL 127 - UL 1482 - ULC S627 - ULC S610

INSTALLATION AND OPERATING INSTRUCTIONS

PARTS REQUIRED:

ü

Fireplace Model

MAGNUM ZC

ü

8” or 7” diameter listed 2100 degree type HT
insulated or air-cooled chimney system

ü

Anchor plate (supplied with chimney system)

ü

4” outside combustion air hookup (supplied by
dealer)

ü

ZC-65 (8” to 7”) chimney adapter if using 7”
chimney system

OPTIONAL ACCESSORIES:

ü

Fan Kit

ü

Brass grills

ü

Brass Trim Kits

ü

Arched Lintel Iron

Содержание ZC







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды