manualshive.com logo in svg

Magnum ZC, Руководство пользователя

Поделиться
Скачать
Magnum ZC Скачать руководство пользователя страница 31

MAGNUMZC MANUAL – April 2006

PAGE  - -

31

THERMO-CENSOR KIT - PROCUDURE FOR INSTALLING

Tools Needed:

 Flat Screwdriver, Drill with ¼” Hex socket driver bit, ¼” socket wrench

Contents of Kit:

 Bracket, Thermo-Censor, Wiring, 1 ¼” tek screw, Romex connector

1)

Unpackage the Thermo-Censor kit and make sure that all the parts are included in the kit.

2)

If the fireplace system has a blower kit installed, make sure to disconnect the electrical supply before installing
the kit.

3)

Open the lower grill and unplug the blower (if installed).  Take the front cover off the electrical box located in the
front right corner of the unit.  Remove the receptacle from the junction box.

4)

Slide the Thermo-Disk bracket up the inside of the fireplace so that the disk is located against the firebox as
shown in Figure 28.  The bracket should be raised just enough to hide the horizontal portion of the bracket and
up against the right flange of the lower grill housing.

5)

Using the ¼” hex socket drive bit in the drill attached the ¼” hex head tek screws making sure that you do not
over tighten the screw and strip it.

6)

Make sure that the two wires coming from the Thermo-Censor are not binding against the side of the unit.  Route
the wires so that they do not touch the firebox of the unit.

7)

Attach the Romex connector to the side of the electrical junction box and route the two wires from the Thermo-
Censor through the connector.  Attach the wires as shown in Figure 29.

8)

Make sure that all electrical connections are proper and secure.  Reverse the procedure to install the electrical
receptacle and cover.  Plug the fireplace blower into the receptacle and connect the electrical supply back to the
unit.

NOTE:

 If the Thermo-Censor does not kick in after 20-30 minutes after the fire is going, check to make sure that the

censor is up against the side of the firebox as shown in Figure 28.  Check all electrical connections to make sure that
everything was installed properly.

FIGURE 28

THERMO-DISC

WIRE PIGTAILS

TO

JUNCTION BOX

#7 HEX SCREW

THERMO-DISK

BRACKET

GRILL

HOUSING

SIDEWALL

POWER

SOURCE

JUNCTION BOX FRONT

RIGHT SIDE OF UNIT

FIGURE 29

FIREPLACE

BLOWER

BLOWER CORD

PLUGS INTO

WHITE

GROUND

BLACK

THERMO

DISC

LOWER

GRILL

FIREBOX

Содержание ZC







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды