manualshive.com logo in svg

Magnum ZC, Руководство пользователя

Поделиться
Скачать
Magnum ZC Скачать руководство пользователя страница 22

MAGNUMZC MANUAL – April 2006

PAGE  - -

22

EXPANDED METAL FACE KIT INSTALLATION

(FOR STONE, BRICK & TILE FACING)

Mesh Kit (ZC-75)

1)

Take the mesh kit and hardware out of the packaging and make sure that all items are included.  Contact your
supplier if any parts are missing.

2)

Align the left & right panels so that the mesh openings are facing upwards and the angle iron is close to the front
face plate of the unit.  Do not butt the angle iron tight against the face plate.  Leave a small amount of expansion
room (1/16” is normal).

3)

Fasten the mesh in place using the self drilling and tapping screws provided.  Screws every 8-10 inches apart is
sufficient.  Do not tighten the screws tight on the face of the unit.  Leave expansion room for the mesh to move
(1/32” is sufficient).

4)

Either wood screws or nails (not provided) can be used to fasten the mesh to the wood studs on the left and right
sides of the unit (these should be tight).

5)

Follow the same procedure for the top panel.

6)

Make sure that the grill opening is aligned parralel and straight with the unit.

WARNING:

Wear gloves when handling / installing the Mesh Kit.  The edges are sharp !!

FIGURE 13

Top

Panel

Front Face Plate of Unit

Lower Grill

Wood

Studs

Damper

Handle

Upper

Grill

Left Side

Panel

Angle Iron

frame

toward

flange of

unit

Mesh facing

upward

Outline of

sides and top

of unit

behind ZC-

Right Side

Panel

Angle Iron

frame

toward

flange of

unit

Mesh facing

upward

Tools needed:

ü

Hand Drill

ü

¼” Nut Driver

ü

(optional)
Hammer and 16
penny nails

ZC-75 Mesh Kit
Includes:

ü

Top Panel

ü

Left Panel

ü

Right Panel

 (36) # 8 tek screws

 Overall width  44.250 in.

Overall Ht.
48.500 in.

Содержание ZC







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды