Magnum ZC Скачать руководство пользователя страница 1

Страница: 1 / 38

MAGNUM

™

(MAGNUM ZERO-CLEARANCE WOOD FIREPLACE)

OWNER’S MANUAL

Installation, Operation and Maintenance Instructions

Safety tested by Warnock Hersey to UL 127-1988, CAN/CSA- ULC S610-M93

Certified to EPA Method 28A & 5G3(exempt status)

Tested by Method 5G for emissions, results 3.490 g/hr

This appliance can be installed in all applications except a mobile home installation or a HUD home. Installations into a

permanent manufactured home is determined by local building authorities

AMERICAN ENERGY SYSTEMS, INC. – 150 Michigan Street N.E. – HUTCHINSON, MINNESOTA 55350

(320) 587-6565 PHONE – (320) 587-8872 FAX

[email protected]

–

www.magnumheat.com

rev date 04/06

PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION

AND USE OF YOUR MAGNUM ZC FIREPLACE. FAILURE TO

FOLLOW THESE INSTRUCTIONS MAY RESULT IN PROPERTY

DAMAGE, BODILY HARM OR EVEN DEATH.

AMERICAN ENERGY SYSTEMS, INC. GRANTS NO WARRANTY,

IMPLIED OR STATED, FOR THE INSTALLATION OR

MAINTENANCE OF THE MAGNUM ZC FIREPLACE AND ASSUMES

NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S).

Содержание ZC







































Результаты поиска

Содержание ZC

Отзывы:

Бренды по названию

Популярные бренды

Magnum ZC, Руководство пользователя

Результаты поиска

Содержание ZC

Отзывы:

Бренды по названию

Популярные бренды