Magnum Energy MM 1212AE Скачать руководство пользователя

Страница: 3 / 44

2006 Magnum Energy Inc

IMPORTANT PRODUCT SAFETY INSTRUCTIONS

This manual contains important safety instructions that must be

followed during the installation and operation of this product. Read all

instructions and safety information contained in this manual before

installing or using this product.

• All electrical work must be performed in accordance with local, state

and federal electrical codes.
• This product is designed for indoor / compartment installation. It

must not be exposed to rain, snow, moisture or liquids of any type.
• Use insulated tools to reduce the chance of electrical shock or

accidental short circuits.
• Remove all jewelry such as rings, watches, bracelets, etc., when

installing or performing maintenance on the inverter.
• Always disconnect the batteries or energy source prior to installing

or performing maintenance on the inverter. Live power may be present

at more than one point since an inverter utilizes both batteries and AC.

Turning off the inverter may not reduce this risk. As long as AC power

is connected, it will pass thru the inverter regardless of the ON/OFF

power switch.
• Always verify proper wiring prior to starting the inverter.
• Do not operate the inverter if it has been damaged.
• Do not dismantle the inverter; there are no user serviceable parts

contained in this product. Attempting to service the unit yourself could

cause electrical shock. Internal capacitors remain charged after all

power is disconnected.
• No AC or DC disconnects are provided as an integral part of this

inverter. Both AC and DC disconnects must be provided as part of the

system installation.
• No overcurrent protection for the battery supply is provided as an

integral part of this inverter. Overcurrent protection of the battery

cables must be provided as part of the system installation..
• No overcurrent protection for the AC output wiring is provided as an

integral part of this inverter. Overcurrent protection of the AC output

wiring must be provided as part of the system installation.

SAVE THESE INSTRUCTIONS

http://www.wholesalesolar.com/inverters.html

Содержание MM 1212AE













































Результаты поиска

Содержание MM 1212AE

Отзывы:

Похожие инструкции для MM 1212AE

Бренды по названию

Популярные бренды

Magnum Energy MM 1212AE, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MM 1212AE

Отзывы:

Похожие инструкции для MM 1212AE

Бренды по названию

Популярные бренды