Magnum Energy MM 1212AE Скачать руководство пользователя

Страница: 12 / 44

2006 Magnum Energy Inc

2.0 Installation

2.0 Installation

Pre-Installation

Before installing the inverter, read

the entire installation section to

determine how you are going to install your MM. The more thorough

you plan in the beginning, the better your inverter needs will be met.

Note: Installations should be performed by qualified person-

nel, such as a licensed or certified electrician. It is the

installer’s responsibility to determine which safety codes

apply and to ensure that all applicable installation require-

ments are followed. Applicable installation codes vary

depending on the specific location and application of the

installation.

Note:

Review the “Important Product Safety Information” on

page ii and the “Important Battery Safety Instructions” on

page iii before any installation.

The basic system diagram shown in Figure 6

should be reviewed to

assist you in planning and designing your installation.

Unpacking and Inspection

• Carefully remove the MM Series inverter from its shipping container

and inspect all contents. Verify the following items are included:

The MM Inverter

Red and black DC terminal covers

AC access cover with two screws

Two 1/2” hex-head kep nuts (installed on the DC terminals).

Battery Temperature Sensor (battery charger models only)

MM Series Inverters, Installation and Operation Guide.

If items appear to be missing or damaged, contact your authorized

Magnum Energy dealer or Magnum Energy.

• If at all possible, keep your shipping box. It will help protect your

inverter from damage if it ever needs to be returned for service.

• Save your proof-of-purchase as a record of your ownership; it will

also be needed if the unit should require in-warranty service.

• Record the unit’s model and serial number in the front of this manual

in case you need to provide this information in the future. It is much

easier to record this information now, instead of trying to gather it

after the unit has been installed.

http://www.wholesalesolar.com/inverters.html

Содержание MM 1212AE













































Результаты поиска

Содержание MM 1212AE

Отзывы:

Похожие инструкции для MM 1212AE

Бренды по названию

Популярные бренды

Magnum Energy MM 1212AE, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MM 1212AE

Отзывы:

Похожие инструкции для MM 1212AE

Бренды по названию

Популярные бренды