Magnum Energy MM 1212AE Скачать руководство пользователя

Страница: 37 / 44

2006 Magnum Energy Inc

ON/OFF Switch

The ON/OFF Switch is a momentary push-button switch that duplicates

the ON/OFF switch on the inverter. This switch also allows additional

changes to be made while in the Invert or Charge Mode.
When the inverter is first connected to the batteries, the inverter and

remote go through an internal 10 seconds start-up test. After this test

is completed, the ON/OFF switch can be pressed to turn on the

inverter. Once the inverter has been turned on, momentarily pressing

the ON/OFF switch alternately turns the inverter On/Standby and Off.
On models with the search mode function, the ON/OFF switch can be

used to enable or disable the search mode. While in the Invert Mode,

pressing and holding this switch for three seconds causes the search

mode to alternate between Disabled (Inverter always on - indicated

by the INVERT LED indicator always on) and 5W (the inverter is

looking for at least a 5 watt load to turn on and start inverting -

indicated by the INVERT LED indicator blinking once a second).
On models with the battery charger feature, this switch can also be

used to put the charger in standby (disables the charger) so that all

the incoming power can be used exclusively for the AC loads. To put

the charger in standby, press and hold the ON/OFF switch for three

seconds (you must be in the Charge Mode). When this happens, the

charging indicators (BULK, ABSORB and FLOAT) will go off. To activate

the charger, press and hold the ON/OFF switch for three seconds

again. When the charger is again activated, one of the charging

indicators will come on to show the current charge stage.

Warning - When any external AC power is passing through

the inverter and present on the output. Pressing the ON/OFF

switch will not remove this AC power on the inverter’s output.

Monitoring the LED Indicators

MM-R and MM-RC Remotes

The three LED indicators on the left side of both the MM-R and MM-RC

remotes (

figure 13)

will show you the operating status of the

Series inverter.

Monitor these indicators to determine the inverter’s

mode of operation:
INVERT (green) -
• On (solid)

- and AC IN LED indicator is Off - The inverter is On. It is using

energy from the battery to supply AC power to the loads connected

to the inverter.
- and AC IN LED indicator is On (solid) - The inverter is in Standby.

The external AC power (Utility or generator) connected to the

inverters input is passing through the inverter to power the AC

loads. The inverter will automatically turn on to power the AC loads

if the external AC power is lost or disconnected.

• Blinks On (once every second) - The inverter is in search mode.

The AC load is below 5 watts (Search Watts default setting).
• Off - The inverter

is disabled. The inverter is not on or will not come

on if AC power is lost or disconnected.

Appendix A - Remote Control and Monitoring

http://www.wholesalesolar.com/inverters.html

Содержание MM 1212AE













































Результаты поиска

Содержание MM 1212AE

Отзывы:

Похожие инструкции для MM 1212AE

Бренды по названию

Популярные бренды

Magnum Energy MM 1212AE, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MM 1212AE

Отзывы:

Похожие инструкции для MM 1212AE

Бренды по названию

Популярные бренды