background image

©

2006 Magnum Energy Inc

.

IMPORTANT

BATTERY SAFETY INSTRUCTIONS

• Wear eye protection such as safety glasses when working with

batteries.
• Remove all jewelry such as rings, watches, bracelets, etc., when

installing or performing maintenance on the inverter.
• Never work alone. Always have someone near you when working

around batteries.
• Use proper lifting techniques when working with batteries.
• Never use old or untested batteries. Check each battery's label for

age, type and date code to ensure all batteries are identical.
• Batteries are sensitive to changes in temperature. Always install

batteries in a stable environment.
• Install batteries in a well ventilated area. Batteries can produce

explosive gasses. For compartment or enclosure installations, always

vent batteries to the outside.
• Provide at least one inch of air space between batteries to provide

optimum cooling.
• Never smoke when in the vicinity of batteries.
• To prevent a spark at the battery and reduce the chance of explo-

sion, always connect the cables to the batteries first. Then connect the

cables to the inverter.

• Use insulated tools at all times.
• Always verify proper polarity and voltage before connecting the

batteries to the inverter.
• To reduce the chance of fire or explosion, do not short-circuit the

batteries.
• In the even of accidental exposure to battery acid, wash thoroughly

with soap and water. In the event of exposure to the eyes, flood them

for at least 15 minutes with running water and seek immediate medical

attention.

• Recycle old batteries.

SAVE THESE INSTRUCTIONS

iii

http://www.wholesalesolar.com/inverters.html

http://www.wholesalesolar.com/inverters.html

Содержание MM 1212AE













































Отзывы: