Magnum Energy ME-BMK Скачать руководство пользователя

Страница: 2 / 24

Disclaimer of Liability

Since the use of this manual and the conditions or methods of installation,

operation, use and maintenance of the ME-BMK is beyond the control of

Magnum Energy Inc., this company does not assume responsibility and

expressly disclaims liability for loss, damage or expense, whether direct,

indirect, consequential or incidental, arising out of or anyway connected with

such installation, operation, use, or maintenance.
Due to continuous improvements and product updates, the images shown in

this manual may not exactly match the unit purchased.

Restrictions on Use

The ME-BMK shall not be used in connection with life support systems, life

saving or other medical equipment or devices. Using the ME-BMK with this

particular equipment is at your own risk.

IMPORTANT PRODUCT SAFETY INSTRUCTIONS

This manual contains important safety instructions that must be followed

during the installation and operation of this product. Read all instructions

and safety information contained in this manual before installing or using

this product.

WARNINGS:

• All electrical work must be performed in accordance with local, state and

federal electrical codes.
• This product is designed for indoor / compartment installation. It must not

be exposed to rain, snow, moisture or liquids of any type.
• Use insulated tools to reduce the chance of electrical shock or accidental

short circuits.
• Remove all jewelry such as rings, watches, bracelets, etc., when installing

or performing maintenance on the ME-BMK and inverter system.
• Always disconnect the batteries or energy source prior to installing or per-

forming maintenance on the ME-BMK and inverter system. Live power may

be present at more than one point since an inverter utilizes both batteries and

AC. Turning off the inverter may not reduce this risk. As long as AC power

is connected, it will pass thru the inverter regardless of the power switch on

the inverter or the ON/OFF INVERTER pushbutton on the remote.

Safety Symbols

To reduce the risk of electrical shock,

re, or other safety hazard, the fol-

lowing safety symbols have been placed throughout this manual to indicate

dangerous and important safety instructions.

WARNING:

This symbol indicates that failure to take a speci

action could result in physical harm to the user.

CAUTION:

This symbol indicates that failure to take a speci

ed ac-

tion could result in damage to the equipment.

Info:

This symbol indicates information that emphasizes or supple-

ments important points of the main text.

http://www.wholesalesolar.com/inverters.html

Содержание ME-BMK

























Результаты поиска

Содержание ME-BMK

Отзывы:

Похожие инструкции для ME-BMK

Бренды по названию

Популярные бренды

Magnum Energy ME-BMK, Руководство пользователя

Результаты поиска

Содержание ME-BMK

Отзывы:

Похожие инструкции для ME-BMK

Бренды по названию

Популярные бренды