Magnum Energy ME-BMK Скачать руководство пользователя

Страница: 7 / 24

Installation

2.0 Installation

Before installing the ME-BMK, read this entire section to be aware of all as-

pects of the installation; then you can thoroughly plan the details to ensure

the overall system requirements are accomplished.
To assist you in planning and designing your installation; you should review

the basic system diagram shown in Figure 2-1. If another network device

besides the ME-BMK is to be installed, refer to section 2.3 to determine your

speci

c network con

guration.

Info:

Installations should be performed by quali

ed personnel, such

as a licensed or certi

ed electrician. It is the installer’s responsibility

to determine which safety codes apply and to ensure that all appli-

cable installation requirements are followed. Applicable installation

codes vary depending on the speci

c location and application.

Info:

Review the “Important Product Safety Information” on the

front inside cover page before any installation.

Review the following guidelines prior to performing the Installation:
• The ME-BMK sense module is connected to the inverter by a 10’ communi-

cations cable and to the DC shunt using a 5’ twisted-pair signal wire. Before

installing the ME-BMK Sense module and connecting any wires, determine:

1) the communications cable route throughout the home or vehicle/boat to

the inverter, and 2) the twisted-pair signal wire route to the ME-BMK shunt.

Info:

The communications cable may be extended beyond the

supplied 10’; but to ensure voltage accuracy, do not extend the 5’

twisted-pair wire used between the DC shunt and sense module.

Info:

For information on the size of the battery cable and overcur-

rent protection device to be used in the installation, refer to the

inverter’s owner’s manual.

2.1 Required Components and Tools

2.1.1 List of supplied components in the ME-BMK (see fi gure 2-1):

• Installation and Operation manual

• Sense Module (with two #8 x 3/4” Phillips mounting screws)

• 500A/50mv DC Shunt (with two #8 x 3/4” Phillips mounting screws)*

• 10ft Communications cable

• 5ft Twisted-pair (blue and orange color) signal wires

2.1.2 List of other Required Equipment and Materials:

• Magnum Inverter with network port (ME, MS or RD Series)

• ME-RC (Magnum ME-RC remote display with revision

≥

2.0)

• Batteries (with appropriately sized cables)

• Short (~18”) battery cable (to connect shunt to battery negative)

• In-line fuse holder (with 2-amp DC fuse)

• DC Breaker (or DC fuse and disconnect) for inverter

• Phone-splitter (if using multiple network devices)

2.1.3 Tools Required to install the ME-BMK:

• Flat-blade screwdrivers (1/4” and 1/8” blades)

• #2 Phillips screwdriver

• 9/16” open-end wrench or adjustable crescent wrench

http://www.wholesalesolar.com/inverters.html

Содержание ME-BMK

























Результаты поиска

Содержание ME-BMK

Отзывы:

Похожие инструкции для ME-BMK

Бренды по названию

Популярные бренды

Magnum Energy ME-BMK, Руководство пользователя

Результаты поиска

Содержание ME-BMK

Отзывы:

Похожие инструкции для ME-BMK

Бренды по названию

Популярные бренды