background image

©2007 Magnum Energy Inc. 

5

Installation

2.2 Installation Procedure

Select a location that is dry and away from extreme temperatures to mount the 

ME-BMK Sense Module and DC shunt; using the supplied #8 x 3/4 screws (x4).  

Allow ample room to view the LED on the Sense Module, access the screws and 

bolts on the shunt; and to access the terminal block and the RJ11 port.  

CAUTION: 

Do not mount the ME-BMK sense module in a closed 

battery compartment or in an area 

where water 

or any other liquid 

can enter the ME-BMK sense module and cause shorting or corro-

sion.  The internal circuit board is conformal coated to help prevent 

corrosion, but this failure is not covered by the warranty.

Info: 

Shunts should be mounted in an area where freely circulating 

air is available.  For continuous operation, it is recommended that 

shunts are not used at more than 2/3 of their rated current.  If this 

is not possible, adequate forced ventilation should be provided to 

keep the shunt operating temperature below 60°C.

CAUTION: 

Before beginning the installation, ensure all AC power is 

disconnected from the inverter; and all negative 

and positive battery 

cables are disconnected from the battery bank.

2.2.1 DC Cable connections

1.  Using an appropriate sized cable, wire the inverter’s DC negative terminal 

to the DC Shunt (load side).

Info: 

For the ME-BMK to monitor all load currents, all DC loads - includ-

ing the inverter - must be connected to the load side of the shunt.

2.  Wire the other side of the DC Shunt (battery side) to the battery negative ter-

minal.  Connect 

cables/hardware to the shunt exactly as shown in 

fi

 gure 2-2.

3.  Using an appropriate sized cable, wire the inverter’s DC positive terminal 

to the load side of an appropriate DC disconnect/overcurrent protection device 

(i.e. DC Circuit Breaker or DC disconnect and fuse).
4.  Open the DC circuit breaker (or remove the fuse) and wire its other side 

to the positive terminal of the battery bank.

Battery cable (x2)

Flat washer (x2)

Split-lock washer (x2)

Bolt with 9/16" head (x2)

8-32 x 3/8" 

screw (x2)

Flat washer (x2)

Sense wire with 

ring terminal to 

Sense Module (x2)

Split-lock

washer (x2)

DC Shunt

Figure 2-2, DC Shunt Connections

http://www.wholesalesolar.com/inverters.html

Содержание ME-BMK

























Отзывы: