Magnum Energy ME-BMK Скачать руководство пользователя

Страница: 20 / 24

Operation

5.2 LED Indicator

There is a bi-color LED indicator on the front of the sense module to indicate

the Battery Monitor’s status. When the Sense Module is

rst powered-up, the

LED blinks red and green while going through a self test. Once the self-test

is complete, use the table below along with the

04 BM: Status

display on the

ME-RC to determine the operating status of the ME-BMK.

Table 5-1, LED Indicator Guide

LED

Status

Meaning

OFF

1. No power to Sense Module. Check for correct DC

voltage (7 to 70VDC) and correct polarity from pin 3

(-) to pin 4 (+) on the terminal block; or

2. Ensure the terminal block is correctly seated into

the Sense Module.

Red

ON,

Green

ON,

Red

On,

Green

Power-up sequence (1 second interval between each

color). The Sense module is performing a self-test

and occurs when

rst connected to power.

Green

Normal operation
The Sense Module is transmitting and receiving correctly

with network devices.

Green

BLINKING

Not able to communicate with remote display.
A. If the remote display is off; refer to the remote’s

operation manual for troubleshooting. Ensure inverter

is on and the correct remote communication cable is

connected to the “REMOTE” port on the inverter.
B. If the remote display is on; ensure the remote display

is revision 2.0 or higher. Remote displays with revision

prior to 2.0 are not compatible with the ME-BMK.

Red

The power-up sequence failed.
Unplug the 4-port terminal block from the sense module

and check for correct DC voltage on pins 3 and 4 (must

be between 7 to 70 volts DC depending on the nominal

voltage of the inverter.

Red

BLINKING

No communication or unrecognizable communication

on the network.
1. Check the communication cable; ensure it is con-

nected correctly. If the ME-BMK communication cable

is missing, a standard 2-conductor telephone cable may

be temporarily substituted.

Important: Ensure the RJ11 connector is pushed into the

correct port; you should feel/hear “click” when the con-

nection is made.

http://www.wholesalesolar.com/inverters.html

Содержание ME-BMK

























Результаты поиска

Содержание ME-BMK

Отзывы:

Похожие инструкции для ME-BMK

Бренды по названию

Популярные бренды

Magnum Energy ME-BMK, Руководство пользователя

Результаты поиска

Содержание ME-BMK

Отзывы:

Похожие инструкции для ME-BMK

Бренды по названию

Популярные бренды