background image

214143

2

Revision F

1.2

General Safety

1000004

Figure 1.1: Safety Equipment

CAUTION

The following general farm safety precautions should be part of
your operating procedure for all types of machinery.

Protect yourself.

When assembling, operating, and servicing machinery, wear
all protective clothing and personal safety devices that could
be necessary for the job at hand. Do

NOT

take chances. You

may need the following:

Hard hat

Protective footwear with slip-resistant soles

Protective glasses or goggles

Heavy gloves

Wet weather gear

Respirator or filter mask

1000005

Figure 1.2: Safety Equipment

Be aware that exposure to loud noises can cause hearing
impairment or loss. Wear suitable hearing protection devices
such as earmuffs or earplugs to help protect against loud
noises.

1010391

Figure 1.3: Safety Equipment

Provide a first aid kit in case of emergencies.

Keep a properly maintained fire extinguisher on the machine.
Be familiar with its proper use.

Keep young children away from machinery at all times.

Be aware that accidents often happen when the Operator is
tired or in a hurry. Take time to consider safest way.

NEVER

ignore warning signs of fatigue.

SAFETY

Содержание FM100

































Отзывы: