Maber MB500/120-SP Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 52

Maber MB500/120-SP Скачать руководство пользователя страница 33

33

29.

FAILURES

The potential failures that may occur on the lift can mainly be attributed to the electric
system. In this case is always advisable to contact the manufacturer’s technical support
service.

Part

Control panel

Problem

The deck is jammed

Cause

Electric power supply has failed.

Remedy

Restore power supply.

Part

Control panel

Problem

The deck is jammed

Cause

The fuse has broken

Remedy

Replace the fuse inside the main control panel on the cart.

Procedure

Open the main control panel.

!!! The operation must be only assigned

to workers from the technical support service !!!

Should the deck be elevated you need to climb on it.
Take all the necessary precautions by entering from the nearest storey door.
Move along the column fastened to the safety belt.
Replace the fuse inside the main control panel.
Alternatively:

Release the service motor brake lever (see page 21).

Get down slowly and start to repair.

Part

Emergency brake

Problem

The deck is jammed

Cause

The ratchet gear spring is broken

Remedy

Replace the spring with an original part.

Procedure This operation must be carried out by an authorised and pre-trained

technician

.

To this purpose, move the deck to first storey immediately above.

From the storey where it stops, unload the deck.

Place under the loading deck a steel section beam or a thick wooden plank
measuring approx. 15x15 cm. so as to stop the machinery from falling. The
operator will have to do this operation from the building. Then ENTER the
loading deck fastened to a safety belt.

Remove the guard and replace the spring with an original part.

Otherwise the deck needs to be relowered to ground level.

x

Uncouple the ratchet gear locking the emergency brake,

x

tie the ratchet gear so that it will not recouple,

x

Climb back on the building,

x

Remove the section beam or plank,

x

Relower the deck to ground level controlling it from the ground,

x

Replace the spring with an original part.

COPY

«
...
31
32
33
34
35
...
»

Содержание MB500/120-SP





















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды