Maber MB500/120-SP Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 52

Maber MB500/120-SP Скачать руководство пользователя страница 14

14

10.

MACHINE TRANSPORTATION

The  machine  is  delivered  completely  assembled  (base,  initial  column,  loading  deck)  and
equipped with fittings, fixed to pallets with metal straps; a set of modular elements of the
column is packed under the base, on the same pallet.
The other  modular elements of the column are   packaged (approx. 30 pieces) on another
pallet.
The  pallets  must  be  unloaded  and  handled  by  a  forklift  truck  (

min. required capacity

1000 kg. with protrusion of approx. 1.20 m).

Should machine be moved with a crane or another hook lifting tool,

insert the hook

only in the column flange plates

as shown in the figure below.

11.

PACKAGING

The machine is packaged and fastened with a metal strap. The electric parts and most
delicate components can be protected with a plastic sheet until delivery
Take off the plastic sheet, if present,

and make sure that it is not within children’s

reach

. Remove the packaging only using the containers provided for refuse collection.

Remove the metal fasteners, discard them only after winding and dispose of them
properly.

Make sure that the machine has not been damaged before delivery. If it has, immediately
inform the salesperson or manufacturer before using the machine.
Check that the moving parts of the machine are fitted (adjusting screws, nuts and bolts,
ramps, guards, electric system etc..) and comply with supply specifications.
Check for any discrepancies compared to the ordered equipment. If there are any, always
advise the dealer or manufacturer before use.

COPY

«
...
12
13
14
15
16
...
»

Содержание MB500/120-SP





















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды