Maber MB500/120-SP Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 52

Maber MB500/120-SP Скачать руководство пользователя страница 29

29

24.

NON-ROUTINE MAINTENANCE

At  least  once  a  month,  or  whenever  you  doubt  their  efficiency,  check  the  service  and
emergency brakes work properly.
These  operations  need  to  be  performed  only  by  trained  and  authorised  personnel  since
the efficiency and safety of the machine depend fundamentally on these parts.

All maintenance jobs must be carried out with the deck on the ground, at the bottom
terminal switch, and with the power off (Unplug the power supply cable and switch
off the main power knob on the control panel).

Gear motor:

x

Change oil for the first time after 100 hours of operation.

x

Then change oil every 2000 hours of operation or at least once a year.

x

Empty and fill through the caps provided.

x

The gear reducer is immediately emptied after operation with hot oil to prevent deposits

of dregs.

x

Clean the caps (especially the magnetic cap) before refitting them.

x

We suggest you wash with detergent before refilling with

new lubricant.

Adjusting the Service Brake:

See section “22”, page 27.
Also make sure the distance between magnet and counter
magnet is about 0.2 mm.. The distance is adjusted with the
three screws.

Adjusting the Emergency Brake (Fall Stopper):

x

The machine must be lowered to ground level.

x

Disable the electric power line with the main power knob

door lock on the control panel.

x

Open the emergency brake guard, by removing the

fastening screws.

x

Adjust all brake disc pressure screws

(4)

until the required

load has been reached.

x

Use the lubricator

(5)

to grease the pin of the ratchet gear

(6).

x

Conduct an operational test before using the machine as

described in paragraph 14 (page 19).

In case of damage other non-routine maintenance or repair
jobs must be carried out only by the

technical support service

who will issue a regular

maintenance declaration, and enter it in this manual in the assigned spaces.

COPY

«
...
27
28
29
30
31
...
»

Содержание MB500/120-SP





















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды