Lynx Industries LX5000B Скачать руководство пользователя страница 3

Страница: 3 / 39

To ensure your new opener works as intended, your garage door must be properly installed and balanced.

Before installing your garage door opener, open and close the door manually to ensure it operates smoothly

from top to bottom. A properly balanced door should not take a lot of effort to open or close by hand. The door

should stay in the open and in the closed position without drifting down or creeping up. If a door opens fast, the

door may need spring tension reduced. If the door drops fast, the door may need spring tension increased.

If the door operates properly, then proceed to the installation manual for instructions how to install the opener.

If the operation of the door does not meet these requirements, adjust the spring balance per your door’s

installation manual or call a professional installer to make adjustments before installing the opener.

Instruction manuals are available for download at www.lynx-nsw.com

Once the door is properly balanced and operates smoothly, you may proceed with the installation of your opener.

PRE-INSTALLATION INSPECTION OF YOUR GARAGE DOOR

PRIOR TO OPENER INSTALLATION

Table of Contents

Package Contents

Pre-Installation Inspection

System Features

Tools Needed

Installation Notes

Attaching Opener to Rail

Setting Belt/Chain Tension

Positioning and Installing

Front Wall Bracket

Attaching Rail to Wall Bracket

Positioning Opener End of Rail

Mounting Opener End

Mounting Door Bracket

Wired Wall Station Installation

Wireless Wall Station Installation

Entrapment Warning Label

Safety Beams Installation

Safety

Beams

Wiring

Connecting Trolley to Door

Installing Light Bulbs

Connecting Operator to Outlet

Alignment of Safety Beams

Connecting Door to Trolley

Setting Opener limits

Contact Obstruction Test

Safety Sensor Obstruction Test

Programing Keyless Entry

Installing Keyless Entry

Safety

Instructions

Operating Wireless Wall Station

Customizing the setting

Opener

Controls

Programing for Homelink

Force

adjustment

Programming Wireless Wall Station

or Transmitter(s) to Opener

Maintenance

Accessories

Troubleshooting

Templates

Содержание LX5000B








































Результаты поиска

Содержание LX5000B

Отзывы:

Похожие инструкции для LX5000B

Бренды по названию

Популярные бренды

Lynx Industries LX5000B, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание LX5000B

Отзывы:

Похожие инструкции для LX5000B

Бренды по названию

Популярные бренды