background image

LUTRON

Wallbox Power Module with DALI Control Unit

Installation and Operation Guide

®

Please Read

  The Wallbox Power Module controls six 

to sixteen zones of DALI compliant output 

devices.

  The Wallbox Power Module can control 

up to 64 DALI compliant output devices 

(devices must comply with IEC/EN 60929 

ed. 3.0 2006-01) which can be addressed 

and grouped into zones.

  The Power Module can be configured for 

wired, QS link (HomeWorks

R

 QS only), or 

wireless, RF link (HomeWorks

R

 QS and 

RadioRA

R

 2), communication.

English

Español

Italiano

Français

Deutsch

Model Numbers: 

Ratings: 120–240 V

~

  50/60 Hz  100 mA

 

230 V

~

  50/60 Hz  100 mA

 

Typical Power Consumption *: 7 W (24 BTUs)

 

Power Draw Units (PDUs) **: 0

Output: 

DALI Link: 18 V   250 mA

Codes: 

Install in accordance with all applicable electrical codes.

Environment: 

Ambient operating temperature: 0 °C to 40 °C, 0% to 90%  

 

 

 

humidity, non-condensing. Indoor use only.

LQR-WPM-6D

LQR-WPM-8D

LQR-WPM-16D

LQRK-WPM-6D

LQRK-WPM-8D

LQRK-WPM-16D

LQRM-WPM-6D

LQRM-WPM-8D

LQRM-WPM-16D

LQRN-WPM-6D

LQRN-WPM-8D

LQRN-WPM-16D

LQRQ-WPM-6D

LQRQ-WPM-8D

LQRQ-WPM-16D

Nederlands

Português

 * Typical Power Consumption test conditions: all loads 

off, button LED on.

** For more information about Power Draw Units 

(PDUs), please see the 

HomeWorks

®

 QS Wiring and 

Power Guidelines

 document on the HomeWorks

®

 QS 

Resource Website

中文

 

Содержание LQR-WPM-16D













Отзывы: