Lutron Electronics GRAFIK Eye QS Скачать руководство пользователя

Страница: 27 / 65

GRAFIK Eye

QS Control Unit Installation and Operation Guide 27

Associating wireless occupancy sensors and GRAFIK Eye

QS Wireless control units

(for wireless enabled units only):

1. Make sure the wireless mode of the GRAFIK Eye

QS control

unit is “Enabled”.

2. Enter programming mode.
3. Use the Master buttons to highlight “Sensor setup” and press

the OK button to accept.

4. Use the Master buttons to highlight “Add wireless sensors” and

press the OK button to accept.

5. Press and hold the “Lights Off” button ( on some sensors) on

the occupancy sensor for 6 seconds. The lens will start flashing

and the info screen on the GRAFIK Eye

QS Wireless control unit

will display the sensor’s serial number.

6. Press the OK button on the GRAFIK Eye

QS control unit. A

screen will confirm that the sensor has been assigned.

(To disassociate a wireless occupancy sensor from the GRAFIK

Eye

QS control unit, Refer to the Radio Powr Savr

occupancy

sensor install guide to return the sensor to its “out-of-box”

functionality. Doing so will remove its programming from the

GRAFIK Eye

QS control unit.)

7. Repeat the above steps for all desired sensors.
8. Exit programming mode.

Associating wireless occupancy sensors through

QS Sensor Modules (QSM):

1. Press and hold the Program button on the QSM for 3 seconds

to enter programming mode. There will be 1 audible beep

and the Status LED will begin flashing. The info screen on the

GRAFIK Eye

QS control unit will display that the QSM is in

programming mode.

2. Press and hold the “Lights Off” button ( on some sensors) on

the occupancy sensor for 6 seconds. There will be 3 audible

beeps from the QSM to verify association.

3. Press and hold the Program button on the QSM for 3 seconds

to exit programming mode.

Note:

The wireless signal has a range of 9 m through standard

construction or 18 m line of sight.

Occupancy Sensor Setup

9-16

1-8

Master

buttons

button

Timeclock

(back) button

Main menu

Zone Setup

Sensor Setup

Occupancy

xxxx-xxxx

Press OK to Save

Add wireless sensors

Initiate association

of sensors

Saved

*Assigned*

Sensor Setup

Daylight

Add wireless sensors

Program button

Press and hold

“Lights Off” or

button to associate/

disassociate

QS Sensor Module (QSM)

Radio Powr Savr

Occupancy Sensors

Содержание GRAFIK Eye QS


































































Результаты поиска

Содержание GRAFIK Eye QS

Отзывы:

Похожие инструкции для GRAFIK Eye QS

Бренды по названию

Популярные бренды

Lutron Electronics GRAFIK Eye QS, Инструкция по установке и эксплуатации

Результаты поиска

Содержание GRAFIK Eye QS

Отзывы:

Похожие инструкции для GRAFIK Eye QS

Бренды по названию

Популярные бренды