Lutron Electronics GRAFIK Eye QS Скачать руководство пользователя

Страница: 59 / 65

GRAFIK Eye

QS Control Unit Installation and Operation Guide 59

Diagnostics and Special Settings

Enabling/Disabling the Timeclock

The timeclock can be enabled or disabled as desired.

1. Enter programming mode. Use the Master

buttons to select “Timeclock.” Press the OK

button to accept.

2. Use the Master buttons to highlight either

“Enabled” or “Disabled”. Press the OK

button to accept. The info screen will

confirm that your setting has been saved.

3. Exit programming mode.

Master

buttons

button

Saved

Monday

Timeclock

Enabled

Enabling/Disabling the Backlighting

The backlighting on the info screen can be enabled or disabled as

desired.

1. Enter programming mode and select

“Backlighting”. Press the OK button to

accept.

2. Use the Master buttons to highlight either

“Enabled” or “Disabled”. Press the OK

button to accept. The info screen will confirm

that your setting has been saved.

3. Exit programming mode.

Saved

Monday

Backlighting

Enabled

Diagnostics

If you are having trouble with your control unit and call

Lutron Technical Support, you may be asked for diagnostic

information about your unit.

1. Enter programming mode and

select “Diagnostics”. Press the OK

button to accept.

2. Use the Master buttons to highlight

the option that will display the

required information. The info

screen can display the device serial

number, link information, code

version, or USB status. There is

also an option to reset the USB

connection (do this only if asked to

by Lutron Technical Support).

3. Exit programming mode.

Link info

Diagnostics

Device SN

Link Info

Содержание GRAFIK Eye QS


































































Результаты поиска

Содержание GRAFIK Eye QS

Отзывы:

Похожие инструкции для GRAFIK Eye QS

Бренды по названию

Популярные бренды

Lutron Electronics GRAFIK Eye QS, Инструкция по установке и эксплуатации

Результаты поиска

Содержание GRAFIK Eye QS

Отзывы:

Похожие инструкции для GRAFIK Eye QS

Бренды по названию

Популярные бренды