Lutron Electronics GRAFIK Eye QS Скачать руководство пользователя

Страница: 63 / 65

GRAFIK Eye

QS Control Unit Installation and Operation Guide 63

Troubleshooting (continued)

Troubleshooting: Wireless Functions

(for wireless enabled units only)

Device does not respond to

infrared controls

IR Receiver is disabled

Enable the IR receiver

Miswire or loose connection on rear IR terminal

Verify rear IR terminal wiring

Security lockout from

programming mode

Security password set incorrectly

Call Lutron Technical Support to reset password

Symptom

Possible Causes

Solution

Symptom

Possible Causes

Solution

Cannot associate a

wireless device to a unit

Unit does not support wireless functionality

Verify the unit says “GRAFIK Eye

QS Wireless” on the front label.

Unit in incorrect wireless mode

Change wireless mode to “Enabled”

Maximum number of devices have been

associated with unit

Remove devices or associate with a different unit

Wireless device is out of range

Verify wireless device is in range: 30 feet (9 m) through standard construction, 60 feet (18 m)

line of sight)

Associated wireless

devices do not control unit

Wireless device has been unassigned from unit

Reassign wireless device to unit

Devices are not receiving power

Check wireless device’s battery/power wiring

Unit in incorrect wireless mode

Change to correct wireless mode (“Ignore Programming” or “Enabled”)

Multiple devices are associated to the unit with

contrasting settings

Verify the settings of wireless devices are consistent

Wireless device is out of range

Verify wireless device is in range: 9 m through standard construction, 18 m line of sight)

Radio Powr Savr

daylight sensors not in

calibration mode

Follow instructions to calibrate daylight sensors

Wireless devices operate

incorrectly
Wireless devices selectively

operate

System is not configured correctly

Make sure wireless device settings are programmed as desired

Intended settings were not saved

Reprogram wireless device settings

Wireless devices not located correctly

Follow instructions for each device to verify it is located for ideal performance

Info screen often prompts

for wireless device

association

Unit wireless mode set to “Enabled” and nearby

wireless systems are being programmed

Change wireless mode to “Ignore Programming”

Содержание GRAFIK Eye QS


































































Результаты поиска

Содержание GRAFIK Eye QS

Отзывы:

Похожие инструкции для GRAFIK Eye QS

Бренды по названию

Популярные бренды

Lutron Electronics GRAFIK Eye QS, Инструкция по установке и эксплуатации

Результаты поиска

Содержание GRAFIK Eye QS

Отзывы:

Похожие инструкции для GRAFIK Eye QS

Бренды по названию

Популярные бренды