background image

Maestro

®

 Occupancy Sensor C•L

®

 Dimmer  

Additional Programming, Installation, and Troubleshooting Help

Application Note #480

Revision A

January 2013

1

Technical Support — 800.523.9466

Maestro

R

 Occupancy Sensor C•L

R

 Dimmer Models 

MSCL-OP153M; MSCL-OP153MH

Overview

This document serves as a supplement to the Maestro

®

 Occupancy Sensor C•L

®

 Dimmer instruction sheet. 

Occupancy Sensor 

C•L

R

 Dimmer

Tap Button

Raise Button

Lower Button

FASS

T

 

Front Accessible 
Service Switch

Indicator 
Lights (IL)
IL1 - IL7

Note:

       

            •   To replace fixture bulb(s), power may be temporarily disconnected at the light fixture by pulling the FASS

T

 OUT 

on the dimmer.

            •   For any procedure other than routine bulb replacement, power MUST be disconnected at the main electrical panel.

Glossary ................................................................Page 2
Explanation of Sensor Features..........................Page 3
Dimming Features/Sensor Coverage .................Page 5
Sensor Dimmer Programming Mode .................Page 6
Advanced Programming Mode ..........................Page 8
        Preset Light Level .......................................Page 9
        Manual Fade ON Time ...............................Page 11
        Manual Fade OFF Time..............................Page 12
        Delayed Fade to OFF .................................Page 13
        Enable/Disable Indicator Lights .................Page 14
        Low-End Trim .............................................Page 15
        High-End Trim ............................................Page 16
Low-End Trim Shortcut ......................................Page 17
Restoring Default Settings ..................................Page 18
Additional Wiring Diagrams  
and Installation Help ........................................... Page 19
Troubleshooting ..................................................Page 21

7

1

L

R

T

FASS

TM

Содержание C-L
























Отзывы: