LS tractor MT5 Series Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 192

LS tractor MT5 Series Скачать руководство пользователя страница 86

3 - 42

(4) Remote control lever and Quick coupler (optional)



These levers are used to operate the hydraulic cylinder and/or motor of the implement attached to
the tractor.



Push the remote control lever forward, and the hydraulic pressure can be delivered to the left-hand

coupler of the related lever and right-hand coupler shall be connected to the drain.



Each lever of the remote control valve can be operated respectively, and when operating the levers
at the same time, the one received less pressure begins to start first.



According to the valve type, the remote control lever has different operation type.
- Spring return type, Detent type and Detent with auto release type.



After connecting and preliminary operating the hydraulic equipment, check again transmission oil
level of the tractor.

Push

Pull

Lever

③

Lever

②

Lever

①

When pulling

When pushing

Lever

③

Lever

②

Lever

①

Warning

▶

Before removing hydraulic pipes or hoses and other parts, make sure to check that

hydraulic pressure is relieved completely. The leaks of pressurized oil can cause a
fatal physical injury.

▶

Use proper protection equipments, before servicing hydraulic system.

▶

Before connecting or disconnecting the hydraulic quick coupler, lower the

implements to the ground, and check that hydraulic pressure is relieved.

«
...
84
85
86
87
88
...
»

Содержание MT5 Series

































































































































































































Отзывы:

Нет отзывов