LS tractor MT5 Series Скачать руководство пользователя страница 106

Страница: 106 / 192

4 - 4

Position control
lever

4-2. How to drive and stop

▶

Release the clutch pedal slowly. If releasing the clutch pedal suddenly, the gear life

shall be reduced and it may cause a sudden start.

Notice

Throttle pedal

Clutch pedal

Brake pedals

F/R shuttle lever

Throttle lever

Parking brake
lever

Main gear
shift lever

(1) How to drive

①

Synchro-shuttle model

1. Lift up all the implements

(front/middle/rear) from the ground

after starting engine.

2. Pull throttle lever to low speed

position.

3. Press clutch pedal fully.

4. Place each transmission gear

lever (Main, Range, Creeper,

Shuttle lever) on a suitable position.

5. Press brake pedals and release

the parking brake lever.

6. Release clutch pedal slowly with

pressing throttle pedal slowly.

Содержание MT5 Series

































































































































































































Результаты поиска

Содержание MT5 Series

Отзывы:

LS tractor MT5 Series, Руководство оператора, Страница: 106 / 192

Результаты поиска

Содержание MT5 Series

Отзывы: