LS tractor MT5 Series Скачать руководство пользователя страница 40

Страница: 40 / 192

2 - 5

(3) Seat belt

Always wear the seat belt before operating the

tractor and adjust the belt to fit the operator.

1. Insert the seat belt end into the buckle until a

“click” indicates it is properly engaged.

2. To remove the seat belt from the buckle,

press the red release button on the buckle.

Check the seat belt regularly. If damaged or

frayed, replace it with a new one.

Warning

▶

If not wearing the seat belt, it may cause serious injury in case of accident.

- During operation, it must be required to wear seat belt with a cab or safety frame

installed.

- After wearing the seat belt, adjust the belt to fit the operator.

▶

If safety frame is folded down for frame model, do not wear the seat belt.

Buckle

Seat belt

Buckle

Seat belt

STD

OPT

Содержание MT5 Series

































































































































































































Результаты поиска

Содержание MT5 Series

Отзывы:

LS tractor MT5 Series, Руководство оператора, Страница: 40 / 192

Результаты поиска

Содержание MT5 Series

Отзывы: