LS tractor MT5 Series Скачать руководство пользователя страница 101

Страница: 101 / 192

3 - 57

(4) Error Diagnosis Code (EHL)



If the EHL sensor or valve has failed, the error

code shall be displayed on the Instrument panel
as shown in the figure.



In case of several errors, the errors shall be

displayed repeatedly every 1 second. In this
case, record all error codes.



And, contact your authorized local dealer for

check and tell the error code.

SPN

FMI

Component

Description (ENG)

Position sensor short to ground

Position sensor Short to power source

Over the normal operating region (Position sensor)

Below the normal operating region (Position sensor)

Error for position vaue variation rate.

Need for calibration

Out of Calibration

Draft sensor short to ground

Draft sensor short to power source

Over the normal operating region (Draft sensor)

Below the normal operating regint (Draft sensor)

Need for calibration

Out of Calibration

Depth sensor short to ground

Depth sensor short to power source

Over the normal operating region (Depth sensor)

Below the normal operating regint (Depth sensor)

Need for calibration

Out of Calibration

Slope sensor short to ground

Slope sensor short to power

Stroke sensor short to ground

Stroke sensor short to power source

Over the normal operating region (Stroke sensor)

Below the normal operating regint (Stroke sensor)

Need for calibration

Out of Calibration

Up valve short to ground

210300

Depth Sensor

210400

Slope Sensor

210500

Stroke Sensor

210100

Position Sensor

210200

Draft Sensor

SPN code

FMI Code

Содержание MT5 Series

































































































































































































Результаты поиска

Содержание MT5 Series

Отзывы:

LS tractor MT5 Series, Руководство оператора, Страница: 101 / 192

Результаты поиска

Содержание MT5 Series

Отзывы: