LS tractor MT345E Скачать руководство пользователя страница 192

Страница: 192 / 214

5 - 52

Chassis main fuse

②

Chassis main fuse



Chassis main fuse is attached to the left-hand

main harness.



Pull out the chassis main fuse. If necessary,
replace it with a genuine part.

Rated capacity : 50 A



The chassis main fuse is an important part to

protect the electric system of the driver station
and lights. if damaged, check if there is a trouble
in the electric system. Contact your authorized
local dealer for check.

③

ECU main fuse



ECU main fuse is installed to the battery cable
(+).



Remove the cover and pull out the ECU main
fuse. If necessary, replace it with a genuine part.

Rated capacity : 50 A



The ECU main fuse is an important part to

protect the ECU electric circuit. if damaged,
check if there is a trouble in the electric system.
Contact your authorized local dealer for check.

ECU main fuse

▶

The main fuse is an important part to protect the electric system and components.

If it is often burn out, contact your authorized local dealer to check the problem.

▶

Do not use a substitute instead of the rated genuine fuse. Do not connect electric

wires to the battery terminals directly. It may cause a fire and serious injury.

Caution

Содержание MT345E























































































































































































































Результаты поиска

Содержание MT345E

Отзывы:

Похожие инструкции для MT345E

Бренды по названию

Популярные бренды

LS tractor MT345E, Руководство оператора

Результаты поиска

Содержание MT345E

Отзывы:

Похожие инструкции для MT345E

Бренды по названию

Популярные бренды