LS tractor MT345E Скачать руководство пользователя страница 113

Страница: 113 / 214

4 - 11

1. Press the clutch and brake pedals. Pull the

throttle lever to “Low speed” position. Place
the shuttle lever, main gear shift lever in
NEUTRAL and PTO switch to “OFF” position.

3. Apply parking brake and release the brake

pedals and clutch pedal slowly.

2. Lower the implements to the ground and

turn key switch to “OFF” position.

(5) Stopping tractor

Mechanical type

1. Release the HST forward/reverse pedal

slowly. Pull the throttle lever to “Low” speed
position. Place the range gear shift lever in
NEUTRAL and PTO switch to “OFF”
position.

3. Apply parking brake and release the brake

pedals slowly.

2. Lower the implements to the ground and

turn key switch to “OFF” position..

HST Type

Brake pedals

Clutch pedal

Throttle lever

Key switch

HST pedals

Throttle lever

Brake pedals

Parking brake lever

Key switch

Release

Parking brake lever

Brake pedals

PTO switch

Caution

▶

DO NOT leave the tractor with the transmission gear is placed in neutral position

and the parking brake not applied. The tractor may roll down.
Apply the parking brake at all times before leaving the tractor.

▶

Remove the ignition key always after stopping engine.

Содержание MT345E























































































































































































































Результаты поиска

Содержание MT345E

Отзывы:

Похожие инструкции для MT345E

Бренды по названию

Популярные бренды

LS tractor MT345E, Руководство оператора

Результаты поиска

Содержание MT345E

Отзывы:

Похожие инструкции для MT345E

Бренды по названию

Популярные бренды