LS tractor MT345E Скачать руководство пользователя страница 191

Страница: 191 / 214

5 - 51

①

Fuse check and replacement



How to change the fuse

1. Remove the fuse box cover.

2. Check each fuse and remove the damaged one.

3. Replace it with a new one of the same capacity

as the damaged one.



Chassis fuse box is installed under the front
console cover.



The capacity and function of each fuse is
described on the fuse box cover.

(2) Fuse & Main fuse

Chassis fuse box

< Chassis fuse box >

▶

If the same function fuse is damaged repeatedly, contact your authorized local

dealer for check instead of using a substitute such as wire or aluminum foil.

▶

If using the substitute instead of the rated capacity fuse, it may cause a fire which

results in damage of the tractor or personal injury.

Caution

Содержание MT345E























































































































































































































Результаты поиска

Содержание MT345E

Отзывы:

Похожие инструкции для MT345E

Бренды по названию

Популярные бренды

LS tractor MT345E, Руководство оператора

Результаты поиска

Содержание MT345E

Отзывы:

Похожие инструкции для MT345E

Бренды по названию

Популярные бренды