LS tractor MT345E Скачать руководство пользователя страница 202

Страница: 202 / 214

5 - 62

5-16. Troubleshooting

Warning

▶

To avoid injury due to sudden start, apply parking brake and place the

transmission gear in NEUTRAL position before checking and repairing.

System

Faults

Possible causes

Solutions

Engine

The start motor does
not turn when turning
the key switch.

▲

Start safety switch is not

contacted

▲

PTO switch is not on “OFF”

position

▲

Discharge of battery

▲

Terminal loosened

▲

Key switch failure

▲

Start motor failure

▲

Depress the clutch pedal

fully

▲

Place PTO switch on “OFF”

position

▲

Charge or replace

▲

Tighten

▲

Repair or replace

▲

Repair or replace

The start motor turns
but the engine does
not start.

▲

The battery is weak

▲

bad ground

▲

Improper viscosity of engine

oil

▲

Air in fuel system

▲

Fuel filter clogged

▲

Error in engine body

▲

Fuel cock closed

▲

Charge or replace

▲

Tighten the ground

▲

Replace the oil with proper

viscosity

▲

Bleed the air

▲

Wash or replace the filter

▲

Repair

▲

Open the cock

Engine revolution is
irregular.

▲

Air in fuel system

▲

Fuel filter clogged

▲

Injection nozzle clogged

▲

Fuel leakage

▲

Irregular fuel injection

▲

Bleed air

▲

Clean or replace the filter

▲

Repair or replace

▲

Repair

▲

Repair

Engine turns more
than maximum speed.

▲

Impurities in governor

▲

Repair

Engine stops suddenly
during operation.

▲

Fuel shortage

▲

Fault of nozzle

▲

moving parts failure due to bad

lubrication

▲

Add fuel and bleed air

▲

Repair or replace

▲

Repair

Engine stops at low
rpm.

▲

Fault of High pressure pump

▲

Valve gap is not correct

▲

Poor nozzle pressure

▲

Repair

▲

Adjust the gap

▲

Repair

Содержание MT345E























































































































































































































Результаты поиска

Содержание MT345E

Отзывы:

Похожие инструкции для MT345E

Бренды по названию

Популярные бренды

LS tractor MT345E, Руководство оператора

Результаты поиска

Содержание MT345E

Отзывы:

Похожие инструкции для MT345E

Бренды по названию

Популярные бренды