LS tractor MT345E Скачать руководство пользователя страница 189

Страница: 189 / 214

5 - 49

5-15. General maintenance (When required)

Fuel injection
nozzle

Fuel injection pipes

Fuel return pipe

High pressure pump

Fuel filter

Manual feed pump

to Fuel tank

from Fuel tank

Common Rail

Fuel cooler

(1) Air-bleeding from Fuel system



Air in the fuel system may cause weak fuel injection or a failure of the engine start or stop. To prevent

such a failure, bleed the air from the fuel system.

▶

When changing the fuel filter only, it is not necessary to bleed air from the fuel

injection pipes.

Notice

▶

HIGH PRESSURE FUEL

. When the engine is running, do not loosen the fuel

injection pipes to bleed air from the fuel system.

Danger

▶

Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire.

To help prevent possible injury, turn the key switch off when changing fuel filters or
water separator elements. Clean up fuel spills immediately.

Warning

▶

Do not adjust or modify the fuel injection system arbitrary. It can cause a serious

fault related to engine performance and increase of excessive exhaust emissions.

▶

Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel

system component that will be disconnected. Fit a suitable cover disconnected fuel
system component. Do not fill the new filter with fuel. Invisible fine contaminants
can enter the injection pump and it may cause damage to the fuel injection system.

Caution

Содержание MT345E























































































































































































































Результаты поиска

Содержание MT345E

Отзывы:

Похожие инструкции для MT345E

Бренды по названию

Популярные бренды

LS tractor MT345E, Руководство оператора

Результаты поиска

Содержание MT345E

Отзывы:

Похожие инструкции для MT345E

Бренды по названию

Популярные бренды