I564
GB
I
02
19
11
– Select the submenu and press
to show the parameters.
– Each parameter is shown with code, description and current setting value.
– To modify the setting of one parameter, select it and then press
.
– If the Advanced level access code has not been entered, it is not be possible to enter editing page and an access denied message is be shown.
– If instead, the access rights are confirmed, then the editing screen is shown.
– When the editing screen is displayed, the parameter setting can be modified with
◄
and
►
keys. The screen shows the new setting while a graphic bar shows the setting range, the maximum and minimum,
previous setting and factory default values.
– Pressing
◄
+
, the value is set to the minimum possible while with
+
►
, it is set to the maximum.
– Pressing simultaneously
◄
+
►
, the setting is restored to factory default.
– During the entry of a text string, keys
and
are used to select the alphanumeric character while
◄
and
►
are used to move the cursor along the text string. Pressing keys
and
simultaneously will move
the character selection straight to letter “A”.
– Press
to go back to the parameter selection. The entered value is stored.
– Press
◄
to save all the settings and to quit the setup menu. The controller executes a reset and returns to normal operation.
– If the user does not press any key for more than 2 minutes, the system leaves the setup automatically and goes back to normal viewing without saving the changes done on parameters.
– Remember that, solely for the setup data that can be edited using the buttons, a backup copy can be made in the DCRG8F’s EEPROM. This data can be restored, when necessary, in the work memory. The data
backup copy and restore commands can be found in the commands menu.
Setting: Parameter selection
Setting: Page editing
1 - Parameter code
2 - Current setting value
3 - Selected parameter
4 - Parameter description
1 - Selected parameter
2 - New value entered
3 - Maximum possible setting
4 - Factory default setting
5 - Graph bar of the value-range
6 - Minimum possible setting
PARAMETER TABLES
– Below are listed all the programming parameters in tabular form. For each parameter, the possible setting range and factory default are indicated as well as a brief explanation of the function of the parameter. The
description of the parameter shown on the display can in some cases be different than what is given in the table because of the reduced number of characters available. The parameter code can be used however as
a reference.
Note:
The parameters highlighted in the table with a grey background are essential for the operation of the system. They therefore represent the minimal essential programming for setting in operation.
P01.01
– Select display text language.
P01.02
– Automatic clock setting activation access after power-up.
P01.03
– LCD contrast adjustment.
P01.04
– Display backlight high adjustment.
P01.05
– Display backlight low adjustment.
P01.06
– Low display backlight delay.
P01.07
– Default page display restore delay when no key pressed. If set to OFF, the display will always show the last page manually selected.
P01.08
– Default page displayed at power-up and after delay.
P01.09
– Free text with alphanumeric identifier name of specific panel/system. If a description is set here, it will be shown as title of the main page. The same description is also used as identification for remote
alarm/event reporting via SMS/email.
M01 – UTILITY’ UoM Default Range
P01.01 Language English English
Italian
French
Spanish
Portuguese
German
Polish
Czech
Russian
Custom
P01.02 Set clock at system power on OFF OFF-ON
P01.03 LCD contrast % 50 0-100
P01.04 Display backlight high intensity % 100 0-100
P01.05 Display backlight low intensity % 25 0-50
P01.06 Time to switch to low backlighting s 180 5-600
P01.07 Return to default page s 60 OFF / 10-600
P01.08 Default page main (page list)
P01.09 System description (empty) String 20 chr.
G
B
