background image

 

 

         Doc: I437GB04_16.docx                                      09/03/2016 

p. 25 / 37

 

 

 

47 

Automatic test inhibition 

Prevents automatic test execution. 

48 

LED test 

Lights up all LEDs on the front panel making them blink. 

49 

Close BRK1 

Closes breaker BRK1 in manual mode. 

50 

Open BRK 1 

Opens breaker BRK1 in manual mode. 

51 

Toggle BRK1 

Toggles the state of breaker BRK1 in manual mode. 

52 

Close BRK2 

Closes breaker BRK2 in manual mode. 

53 

Open BRK2 

Opens breaker BRK2 in manual mode. 

54 

Toggle BRK2 

Toggles the state of breaker BRK2 in manual mode. 

55 

Close BRK3 

Closes breaker BRK3 in manual mode. 

56 

Open BRK3 

Opens breaker BRK3 in manual mode. 

57 

Toggle BRK3 

Toggles the state of breaker BRK3 in manual mode. 

58 

Auxiliary voltage ready 

NC contact which, if opened, generates alarm 

A30 Auxiliary voltage breaker alarm. 

Used in combination with the ATLDPS1 alarm relay. 

59 

Service mode 

If enable for system Service, this causes: 

 

Switching to OFF mode 

 

Deactivation of feedback timeout alarms A03 A04 A05  

 

Energising of minimum voltage coils. 

60 

Non-priority load breaker feedback 

Auxiliary contact which informs the ATL of the open/closed state of breaker which 
breaks the non-priority load. If this signal is not connected, ATL considers the state of 
the breaker corresponding to the control output state. 

61 

Maximum priority line SRC1 

When closed, line SRC1 becomes the priority line. 

62 

Maximum priority line SRC2 

As above, referred to line SRC2. 

63 

Maximum priority line SRC3 

As above, referred to line SRC3. 

64 

Tie breaker TB1 feedback 

Auxiliary contact which informs the ATL of the open/closed state of tie breaker TB1. If 
this signal is not connected, ATL considers the state of the tie breaker corresponding to 
the control output state. 

65 

Tie breaker TB2 feedback 

As above, referred to TB2. 

66 

NPL breaker protection trip 

The input generates NPL breaker protection tripping when the contact closes. 

67 

TB1 tie breaker protection trip 

As above, referred to TB1. 

68 

TB2 tie breaker protection trip 

As above, referred to TB2. 

69 

NPL breaker withdrawn   

The input generates NPL breaker withdrawn alarm when the contact opens. 

70 

TB1 tie breaker withdrawn   

As above, referred to TB1. 

71 

TB2 tie breaker withdrawn  

As above, referred to TB2. 

72 

Close TB1 

When in MAN mode, commands TB1 closing. 

73 

Open TB1 

When in MAN mode, commands TB1 opening. 

74 

Toggle TB1 

When in MAN mode, commands TB1 toggle. 

75 

Close TB2 

When in MAN mode, commands TB2 closing. 

76 

Open TB2 

When in MAN mode, commands TB2 opening. 

77 

Toggle TB2 

When in MAN mode, commands TB2 toggle. 

 

 
Programmable input default  
 

Input 

Terminals  Default function 

INP1 

40 

Breaker BRK1 closed (Feedback 1) 

INP2 

41 

Breaker BRK2 closed (Feedback 2) 

INP3 

42 

Breaker BRK3 closed (Feedback 3) 

INP4 

43 

Breaker BRK1 closed (Trip 1) 

INP5 

44 

Breaker BRK2 closed (Trip 2) 

INP6 

45 

Breaker BRK3 closed (Trip 3) 

INP7 

46 

Priority genset start (Off load) 

INP8 

47 

Transfer to secondary load (remote start on-load) 

INP9 

49 

Automatic return to priority line inhibition                 

INP10 

50 Disabled 

INP11 

51 Disabled 

INP12 

52 Disabled 

   

Содержание ATL900






































Отзывы: