The master controller: Wire zone: 01~16(9~16 zones is extended wire zones)
Wireless zone: 21~28
Help: 17
Duress code: 18
Tamper: 30
The keypad: Keypad 1: two-way zone: 31, 41, 42
Keypad 2: two-way zone: 32, 43, 44
Keypad 3: two-way zone: 33, 45, 46
Keypad 4: two-way zone: 34, 47, 48
When the keypad stops working without being cancelled, the master controller will alarm. Use anti-tamper zones:
51, 52, 53, 54 respectively indicating correspondent keypad disconnected.
8.2 Definitions of zone number
9. Keypad operation
Operation display explanation
1. LED displays real-time clock, for example 11:25.
2. In alarm status, the left of the LED displays two digits "- -" and the right displays alarm zone numbers. Buzzer
chirps continually, at the same time correspondent indicator is on. For example, if NO.17 zone alarms, the LED
displays "- - 1 7".
3. Press the "Program" key when system is in disarmed status and password input is right. LED displays'- - - -'
indicate the programming status. The commands and perimeters input will be displayed from the left to the right.
When input more than three digits, the digits will move to the left, the last digit will display "-" but not itself .For
example, when input '1 2 3', displays '1 2 3 -', while input a '4' more, displays '2 3 4 -'.
4. In the programming status, press '#' key to disposal the command and parameters . If the command and
parameters input is fault or can not be performed, the system will exit the programming status automatically and
displays clock, at the same time, buzzer beeps 5 times; Input the right command, buzzer beeps twice and
displays '- - - -'. It is able to exit the programming status by pressing '#' key return to the clock status.
5. Programming or inputting passwords, press '*'key to delete a digit. After deleted all digits, press '*' key to exit
present status and return to display clock.
6. When programming, if the user does not press key in one minute, the system will exit the programming status
and return to display clock.
9.1 Password input
Operation:
"Disarm" or "Program" key
→
user password
→
'#' confirmation.
After pressing " DISARM " or " PROG " key, the system enters password input status '- - - -'. Continue to input
password, and LED displays 'H' from the left to the right, the right side displays '-'. For example, when input 2 digits,
LED displays 'H H - - '. If password is in error, the system exits input status and displays clock and buzzer beeps 5
times. If input wrong password for 5 times continuously, the keypad can not operate with password in 30 minutes.
Restart the system unlock the keypad .when the keypad is locked, press any keys in the keypad the backlight will
flashes twice. User password is 0808 in factory setting.
9.2 Function key operation
9.2.1 Arm-away
Press 'AWAY key, then the keypad buzzer beeps continuously and the status indicator is on. The
system enters arm-away delay. When arm delay is over, buzzer stops beeping and the system enters
9
12
9.3.1 Alarm telephone number Setting/canceling Input: 11 XY...Y
(1) Set alarm phone number
Operations: (PROG
→
user password
→
#)
→
11
→
XY...Y
→
#
Bracket means in programming status, it is not necessary to input 'PROG
→
user password
→
#', enter command
status directly.
Parameters setting:
X=1~6, indicates 1~6 groups telephone, 1 is alarm number of the alarm center, 2~6 are
personal phone numbers.
Y...Y:
indicates phone number needed to dial (1~15 digits), phone number is null in factory setting.
Functions:
The system can be set 6 groups of alarm phone number. NO. 1 is for the alarm center. If user sets the
first number, when alarm happens, the system will announce the alarm center and sent out alarm information
according to ADEMCO Agreement. If user does not open service of the alarm center, the system begins to dial
number from NO.2 according to alarm information set. After putting through a phone, the system plays
corresponding alarm sound. If user does not deal with alarm information, the system will continually dial the
number set 5 times.(refer to Remote phone operation).
For example:
if user wants to set NO2&3, operation as followed: Program
→
User password
→
#
→
11
→
2
→
phone
number
→
#
→
11
→
3
→
phone number
→
#
Note:
In duress alarm status, the telephone will not dial the second, the third and the fourth these three groups of
telephones but the alarm center, the fifth, the sixth group of telephones. Recommended: the fifth, the sixth group of
telephone numbers should not be set like the personal mobile phone number.
(2) Alarm telephone number cancel
Operations:
(PROG
→
User password
→
#)
→
11
→
X
→
#
, Parameters setting: X=1~6, indicates 1~6 groups
telephone 1 for the alarm center, 2~6 for personal telephone numbers.
9.3.2 User address code setting Enter:20 XXXX
Operations: (PROG
→
user password
→
#)
→
20
→
XXXX
→
#
Parameter definition:
XXXX = 4 digits user code. The factory setting is 1234.
Functions:
After setting user code, when alarm happens, the alarm center will distinguish which master controller is
9.3.3 User password modification Enter:21 XXXX
Operations: (PROG
→
user password
→
#)
→
21
→
XXXX
→
#
Parameters definition:
XXXX = 4 digits code. The factory setting is 0808
Functions:
User can modify user password which ensure user's absolute authority to operate the system. User
must hold password to operate the system. After setting password, user should ensure its safety and reliability.
Duress password:
When user is under duress, user can press 'Disarm' key and input duress password. The control
panel will display 'Disarm', send out alarm message to the alarm center or the receiver and keep alarm record (the
zone number is 18). Duress password can be used to disarm but set parameters. Duress password is the last digit
of user password plus 1, no carry, i.e. 9+1=0.
For example:
If user password is 8889, corresponding duress password is 8880; if user password is 9999,
corresponding duress password is 9990.
Restore password in factory setting:
Hardware restores factory setting. There is a jumper 'CB400' on PCB of the
master controller. Normally the jumper is in 'USE' mode, if user forgets password, he/she should turn off system
power, turn jumper to 'DEFAULT' mode, then enable the system again to restore user password in factory setting.
After the system is initialized successfully, user should turn jumper to 'USE' mode, or the system will restore
Содержание LHD6000
Страница 2: ...INSTALLATION MANUAL ...
