LOFTNESS Battle Ax 207460 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 66

LOFTNESS Battle Ax 207460 Скачать руководство пользователя страница 31

27

Battle Ax Skid Loader OM

Installing/Removing the Hood Liner

(Cont’d)

Mounting the Hood Liner

Remove the motor cover to access some hardware
locations that are used to secure the hood liner. Refer to
“Removing Motor Cover” on page 22 for instructions.

Rotor partially hidden in this image for clarity.
The rotor does not need to be removed to
install or remove the hood liner.

NOTE:

2 3

4 5

1

A

A

NOTE:

Before installing the hood liner, remove the
factory-installed hardware shown at the locations
above (A). This hardware is no longer used.

There are fourteen hardware locations for the
61" Battle Ax, and sixteen locations for the 71"
Battle Ax.

Clean the rotor chamber as well as all hardware locations
shown above.

Place the hood liner (1) into position, then align the holes
in the hood liner with the threaded holes in the frame
made available after removing the factory-installed
hardware.

Install the supplied 1-3/4" bolts (2) with 1/2" washers (3)
through the back of the liner and into the threaded holes
on the frame. Then install the 1-1/4" bolts (4) with 1/2"
washers (5) through the top of the frame and into the
weld nuts on the hood liner. Tighten securely.

Retightening/Reinstalling the Cutter Bar

and Recutter

If the hood liner was installed onto a new or unused
Battle Ax,

retighten all hardware securing the cutter bar.

If the hood liner was installed onto a Battle Ax that
has been used or already put into service,

make sure

all contact surfaces on the cutter bar, the recutter, and
on the Battle Ax have been thoroughly cleaned and are
clear of debris.

Remount the cutter bar. See “Cutter Bar Adjustment/
Removal” on page 15 for installation instructions.

Remount the recutter. See “Recutter Removal/
Replacement” on page 26 for installation instructions.

Maintenance

«
...
29
30
31
32
33
...
»

Содержание Battle Ax 207460



































































Отзывы:

Нет отзывов