LOFTNESS Battle Ax 207460 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 66

LOFTNESS Battle Ax 207460 Скачать руководство пользователя страница 19

15

Battle Ax Skid Loader OM

Cutter Bar Adjustment/Removal

1

2

NOTE:

The cutter bar can be adjusted back or forward
to increase or decrease the distance between
the bar and the rotor.

Most operators find the best performance is
achieved by adjusting the cutter bar as close
as the slots will allow (approximately a 1/4" gap
from knife to cutter bar). A wider gap generally
increases finished partical size and horsepower
requirements.

WARNING:

Shut down and disconnect

hydraulic hoses from skid loader before
adjusting the cutter bar.

Loosen the seven bolts with washers (1) securing the
cutter bar (2) to the frame. Move the cutter bar either
forward or back making sure the distance moved is
consistent through the entire length of the cutter bar.
Retighten bolts. Torque to 165 ft.-lbs.

Over time, the cutter bar edge will become worn and
rounded from use. There are a total of 4 wear edges
available by removing and flipping the bar, side to side
and front to back.

CAUTION:

If adjusting the cutter bar after the

machine has been used, the cutter bar should
be completely removed to clear any debris
away from contact surfaces before assembly
and tightening. FAILURE TO DO SO COULD
RESULT IN SEVERE DAMAGE TO THE
MACHINE!.

Set-up Instructions

«
...
17
18
19
20
21
...
»

Содержание Battle Ax 207460



































































Отзывы:

Нет отзывов